Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL) Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)

Camshaft Position Sensor for Nissan Patrol Gu Y61 ZD30 Crd (Common RAIL)

Part #: CSCA545 OEM #: 23731-DB00A SKU: CSCA545

ZD30 CRD Camshaft Position Sensor for Patrol GU Y61

$79.10
RRP $182.11
SAVE $103.01 (57%)
In Stock

BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT NISSAN PATROL Y61 GU 3.0L ZD30 2000-2016 DIESEL Engines

 

TO SUIT:

  • Nissan Patrol GU Y61 [2000-2016] 3.0L ZD30 Diesel
  • Nissan Navara D40 [2010-2015] 3.0L V6 dCi Diesel
  • Nissan Pathfinder R51 [2010-2013] 3.0L V6 dCi Diesel
  • Infiniti FX30d QX70 [2010-Onwards] 3.0L V6 dCi Diesel

 

OEM#

23731-DB00A, 23731-DB000, 23731-BN701, 23731-EN215

93161772, 93179803, 93198004

 

PACKAGE INCLUDES:

1 X OEM Quality CAMSHAFT POSITION SENSOR (3-PIN PLUG).

The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. The engine control unit knows when the first cylinder is at the top dead point through the combination of both sensor signals.

COMMON QUESTIONS

What are the symptoms of a failing Nissan diesel camshaft sensor?

A failing cam sensor often causes extended cranking times intermittent stalling when the engine gets hot or a sudden loss of power accompanied by a Check Engine Light.

How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA545
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCSCA545
Reference OEM Number23731-DB00A
Other OEM Numbers23731-DB00A, 23731BN701, 2376000QAB
Related Part Numbers0986280433, CSCA545, SC434, CAM-133
Trade Part NumbersNTY: ECP-NS-013, VEMO: V46-72-0036
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
TypeSensor
FeaturesDirect Fit
Manufacturer Warranty1 Year
Number of pins3 -pin connector
Connector Shapeoval
Supplementary Article Infofor camshaft, without cable, with seal ring
Fitting Depth28 mm
Rated Voltage12 V
Housing ColourBlack
Operating ModeElectric
Number of mounting bores1
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category