







Crankshaft Sensor for HSV VS 5.0L V8 LB9 304 Statesman Berlina 10456161
Direct Fit Replaces 10456161
BRAND NEW *OEM Quality* Crankshaft Position Sensor to suit Holden and HSV VS 5.0L V8 304 engines.
Misfiring under load or poor fuel efficiency on your 5.0L V8? A failing crankshaft sensor is a common cause on the 304. This is a direct-fit replacement, dispatched same-day before 12pm from Cranbourne VIC.
TO SUIT
This sensor suits the Holden Commodore VS and Statesman VS with the 5.0L V8 GMH 304, built 04/95 to 06/99. It also covers the HSV Manta VS, Senator VS and Statesman VS 185i with the VU and GMH308 5.0L V8.
FITMENT CHECK
This is the V8 application of the sensor. The 3.8L V6 Commodore and Statesman use the same part number but are listed separately - check your engine before ordering.
OEM PART NUMBERS
- 10456161
- 12567649
- 24506905
OTHER PART NUMBERS
- BOSCH: F005X03175
- VEMO: V51-72-0196
- ACDelco: 213-151
- WALKER PRODUCTS: 235-1019
- NTK-AU: EH0147
PACKAGE INCLUDES
1 x Crankshaft Position Sensor - 4-pin oval connector, without cable.
ABOUT THIS SENSOR
The crankshaft position sensor sends rapid position and speed updates to the ECU for accurate spark timing. On the 304 V8 the sensor works against far more rotating mass than the V6, so a degraded unit cannot keep the signal clean during heavy acceleration.
This is why V8 failures usually announce themselves as a misfire or flat spot under throttle rather than the hot-start refusal typical of the V6 cars. It is a plug-and-play electronic replacement requiring no ECU programming.
COMMON SYMPTOMS OF FAILURE
- Engine misfires under load or at wide throttle
- Flat spot during hard acceleration
- Poor fuel efficiency
- Check engine light with DTC P0335 or P0336
- Difficulty starting the vehicle
- Intermittent stalling
- [1995 - 1997] HOLDEN BERLINA VS Sedan 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1997] HOLDEN BERLINA VS Wagon 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1997] HOLDEN CALAIS VS Sedan 5.0 i V8 (5.0L V8 GMH 304 165kW)
- [1997 - 1997] HOLDEN CALAIS VS Sedan 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1999] HOLDEN CAPRICE VS Sedan 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1996] HOLDEN COMMODORE VS Ute 5.0 i V8 (5.0L V8 GMH 304 165kW)
- [1995 - 1997] HOLDEN COMMODORE VS Sedan 5.0 i V8 (5.0L V8 GMH 304 165kW)
- [1995 - 1997] HOLDEN COMMODORE VS Sedan 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1997] HOLDEN COMMODORE VS Wagon 5.0 i V8 (5.0L V8 GMH 304 167kW)
- [1996 - 2000] HOLDEN COMMODORE VS Ute 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1997 - 2000] HOLDEN COMMODORE VS Ute 5.0 i V8 (5.0L V8 GMH 304 179kW)
- [1995 - 1999] HOLDEN STATESMAN VS Sedan 5.0 i V8 (5.0L V8 GMH 304 168kW)
- [1995 - 1997] HSV CLUBSPORT VS Sedan 5.0 i V8 (5.0L V8 GMH308 185kW)
- [1995 - 1997] HSV CLUBSPORT VS Wagon 5.0 (5.0L V8 GMH308 185kW)
- [1996 - 1999] HSV GRANGE VS Sedan 5.0 (5.0L V8 VU 185kW)
- [1995 - 1999] HSV MALOO VS Ute 5.0 i V8 (5.0L V8 VU 185kW)
- [1995 - 1997] HSV MANTA VS Sedan 5.0 i V8 (5.0L V8 VU 185kW)
- [1995 - 1997] HSV MANTA VS Wagon 5.0 i V8 (5.0L V8 VU 185kW)
- [1995 - 1997] HSV SENATOR VS Sedan 5.0 i V8 (5.0L V8 VU 185kW)
- [1995 - 1996] HSV STATESMAN VS Sedan 185i 5.0 (5.0L V8 GMH308 185kW)
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA04-5 |
| Barcode # | 9311831174633 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CSCA04 |
| Reference OEM Number | 10456161 |
| Other OEM Numbers | 10456161, 12567649, 24506905 |
| Related Part Numbers | CAS-002, EH0147, CAS1045, SC021, CSCA04 |
| Trade Part Numbers | BOSCH: F005X03175, VEMO: V51-72-0196, ACDelco: 213-151 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CRANKSHAFT POSITION SENSOR |
| Manufacturer Warranty | 1 Year |
| Ean | 9311831174633 |
| Fitting Position | FRONT |
| Number of pins | 4-Pin |
| Connector Shape | oval |
| Supplementary Article Info | without cable |
| Rated Voltage | 12 V |
| Housing Colour | Black |
| Compatible Makes | Holden |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.