Oil Level Sensor for BMW X3 E83 X5 E53 3.0d 530d X1 E84 320d Diesel 12617508003
OEM Spec Fit Replaces 12617508003
BRAND NEW *OEM Quality* oil level sensor to suit BMW M57, M47 and N47 diesel engines in the X3, X5, X1 and 5 Series.
Diesel BMWs lean hard on the oil level sensor for service and warning logic, so a faulty one gives constant nuisance warnings. Packed and sent out same day from Victoria.
TO SUIT
Made for the BMW X3 E83 2.0d and 3.0d, X5 E53 3.0d and E60 530d with the M57 or M47 diesel. It also suits the E90 320d (M47, 2004-2007), the X3 xDrive20d and xDrive30d, and the X1 E84 sDrive18d, sDrive20d, xDrive20d and xDrive23d with the N47, plus the 1 Series 118d, 120d and 123d.
FITMENT CHECK
On the 1 Series diesels the fit can vary with build date. Before ordering, check the number on your old sensor matches 12617508003 or an OEM number below, and compare the photos with your original part.
OEM PART NUMBERS
- 12617508003
- 12611433596
- 12611439810
- 12617832375
- 13617832205
- 7508003
- 1439810
- 7832205
- 7832375
OTHER PART NUMBERS
- V20-72-0462
- 6PR 007 868-031
- EPO-BM-000
- 20 92 3907
- 23907
- 501 522
- 314 800 0051
- LS119
- OLS1000
- OPS180
PACKAGE INCLUDES
1 x oil level sensor with seal ring, 3-pin D-shaped connector, 3 mounting bolt holes.
ABOUT THIS SENSOR
Bolted into the sump, the sensor measures oil level and temperature for the cluster. On the M57 and N47 diesels that reading also matters when checking oil after DPF regeneration, which can raise the oil level with fuel.
A failed sensor shows a steady or random low-oil message, or no reading at all, which makes it impossible to spot oil dilution or a real loss.
COMMON SYMPTOMS OF FAILURE
- Check Control message asking you to check the engine oil level when the dipstick shows it is correct
- Oil level warning that appears only on longer runs or after a DPF regeneration
- No oil level reading in the instrument cluster or on-board computer
- Warning stays on after an oil service
- Oil weeping from the sensor seal on the bottom of the sump
- [01/04 - 08/05] BMW X3 E83 3.0d (3.0L 6CYL M57D30 150kW)
- [09/05 - 03/11] BMW X3 E83 3.0d (3.0L 6CYL M57D30 160kW)
- [09/04 - 08/07] BMW X3 E83 2.0d (2.0L 4CYL M47D20 110kW)
- [09/07 - 03/11] BMW X3 E83 2.0d (2.0L 4CYL N47D20 130kW)
- [09/08 - 08/10] BMW X3 E83 xDrive20d (2.0L 4CYL N47D20 130kW)
- [09/08 - 08/10] BMW X3 E83 xDrive30d (3.0L 6CYL M57D30 160kW)
- [10/03 - 09/06] BMW X5 E53 3.0d (3.0L 6CYL M57D30 160kW)
- [09/02 - 09/05] BMW 5 SERIES E60 530d SEDAN (3.0L 6CYL M57D30 160kW)
- [09/05 - 03/07] BMW 5 SERIES E60 530d SEDAN (3.0L 6CYL M57D30 170kW)
- [12/04 - 09/07] BMW 3 SERIES E90 320d SEDAN (2.0L 4CYL M47D20 115kW)
- [12/09 - 06/15] BMW X1 E84 sDrive18d (2.0L 4CYL N47D20 105kW)
- [10/09 - 06/15] BMW X1 E84 sDrive20d (2.0L 4CYL N47D20 130kW)
- [09/09 - 06/12] BMW X1 E84 xDrive20d (2.0L 4CYL N47D20 130kW)
- [07/12 - 06/15] BMW X1 E84 xDrive20d (2.0L 4CYL N47D20 135kW)
- [10/09 - 06/15] BMW X1 E84 xDrive23d (2.0L 4CYL N47D20 150kW)
- [03/07 - 06/11] BMW 1 SERIES E87 118d HATCH (2.0L 4CYL N47D20 105kW)
- [03/07 - 10/10] BMW 1 SERIES E87 120d HATCH (2.0L 4CYL M47D20 N47D20 120kW)
- [03/07 - 10/10] BMW 1 SERIES E87 120d HATCH (2.0L 4CYL N47D20 125kW)
- [03/07 - 06/11] BMW 1 SERIES E87 123d HATCH (2.0L 4CYL N47D20 150kW)
- [10/07 - 09/13] BMW 1 SERIES E82 123d COUPE (2.0L 4CYL N47D20 150kW)
- [09/08 - 12/13] BMW 1 SERIES E88 118d CONVERTIBLE (2.0L 4CYL N47D20 105kW)
- [09/08 - 12/13] BMW 1 SERIES E88 123d CONVERTIBLE (2.0L 4CYL N47D20 150kW)
- IMPORTANT FITMENT NOTE: 1 Series diesel - fit can vary with build date. Check your OEM number and compare the photos with your original part
What does an oil level sensor do?
The oil level sensor monitors the volume of engine oil in the sump and alerts the driver when the level drops below a safe threshold. It provides an early warning before oil level drops low enough to affect oil pressure and cause engine damage. Unlike the oil pressure sensor which monitors operating pressure while the engine is running, the oil level sensor typically reads level when the engine is off or at idle and the oil has settled in the sump.
What are the symptoms of a failing oil level sensor?
Common symptoms include an oil level warning light on the dashboard despite the dipstick confirming correct oil level, no warning light appearing even when oil is actually low, and intermittent warnings that appear when the engine is cold and disappear once the engine warms up. A Check Engine light with oil level circuit fault codes may also be present. Always verify actual oil level with the dipstick before assuming the sensor has failed.
How does the oil level sensor work?
Most modern oil level sensors use a thermistor-based measurement system. A heating element warms the sensor tip and the rate at which heat dissipates indicates whether the tip is submerged in oil or exposed to air - oil conducts heat away faster than air. Some older vehicles use a float-based sensor similar to a fuel level sender. The ECU interprets the sensor signal and triggers the warning light when oil level is below the minimum mark.
Can I ignore an oil level warning if my dipstick shows the oil is correct?
A single occurrence of an oil level warning with a correct dipstick reading suggests a faulty sensor. However do not ignore repeated warnings - recheck the dipstick carefully, ensuring the vehicle is on level ground and the engine has been off for at least five minutes to allow oil to drain back into the sump. If the dipstick consistently shows correct level and the warning persists, replace the sensor. If the dipstick shows low oil, top up immediately.
Is the oil level sensor the same as the oil pressure sensor?
No - they are two completely different sensors monitoring different things. The oil level sensor measures the volume of oil in the sump and is a maintenance warning device. The oil pressure sensor measures the pressure of oil circulating through the engine and is a real-time engine protection device. A low oil level will eventually cause low oil pressure, but the level sensor provides an earlier warning. Most vehicles have both sensors fitted separately.
Does replacing the oil level sensor require draining the engine oil?
On most vehicles yes - the oil level sensor is mounted in the oil sump below the oil level, so the engine oil must be drained before the sensor can be removed without spillage. Use this as an opportunity to perform an oil and filter change at the same time, as draining the oil is the main labour component of a service. Refill with the correct grade and quantity of oil specified for your engine after fitting the new sensor.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCPS180 |
| Reference OEM Number | 12617508003 |
| Other OEM Numbers | 12617508003, 12611433596, 12611439810, 12617832375, 13617832205 |
| Related Part Numbers | LS119, OLS1000, CPS180, EPO-BM-000, OPS180 |
| Interchange Part Numbers | V20-72-0462, 6PR007868031, EPO-BM-000, 20923907, 23907, 501522 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Oil Level Sensor |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Fitting Depth | 90 mm |
| Housing Colour | Black |
| Housing Type | Aluminium Housing |
| Number of mounting bores | 3 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | 1 Series: check OEM no and compare photos with your old part |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.