Oil Level Sensor for BMW E46 320i 325i 330i 325Ci 330Ci M3 M54 S54 12617508003
OEM Spec Fit Replaces 12617508003
BRAND NEW *OEM Quality* oil level sensor to suit the BMW E46 3 Series with the M54 or S54 six-cylinder.
If your E46 keeps flashing a check-oil-level message after a top-up, the sump sensor is the usual culprit. Packed and shipped same day from Cranbourne VIC.
TO SUIT
Built for the BMW E46 320i, 325i and 330i sedan and wagon, the 320Ci, 325Ci and 330Ci coupe and convertible, and the 325ti compact, 2000-2006 with the M54B22, M54B25 or M54B30. It also suits the E46 M3 coupe and convertible with the 3.2L S54.
OEM PART NUMBERS
- 12617508003
- 12611433596
- 12611439810
- 12617832375
- 13617832205
- 7508003
- 1439810
- 7832205
- 7832375
OTHER PART NUMBERS
- V20-72-0462
- 6PR 007 868-031
- EPO-BM-000
- 20 92 3907
- 23907
- 501 522
- 314 800 0051
- LS119
- OLS1000
- OPS180
PACKAGE INCLUDES
1 x oil level sensor with seal ring, 3-pin D-shaped connector, 3 mounting bolt holes.
ABOUT THIS SENSOR
On the E46 the oil level sensor bolts into the bottom of the sump and feeds the oil level check that runs in the cluster each time the car is started.
Age and heat cycling break down the sensor on high-kilometre M54 and S54 engines, giving false warnings or no reading at all. The M3 S54 is sensitive to oil level, so an accurate reading matters.
COMMON SYMPTOMS OF FAILURE
- Check Control message asking you to check the engine oil level when the level is correct
- Low oil level warning that comes and goes after the engine warms up
- No oil level reading in the instrument cluster or on-board computer
- Oil level warning stays on after an oil change or top-up
- Oil weeping from the sensor seal on the bottom of the sump
- [01/00 - 05/06] BMW 3 SERIES E46 320Ci COUPE (2.2L 6CYL M54B22 125kW)
- [09/00 - 02/05] BMW 3 SERIES E46 320i SEDAN (2.2L 6CYL M54B22 125kW)
- [09/00 - 02/05] BMW 3 SERIES E46 320i WAGON (2.2L 6CYL M54B22 125kW)
- [09/00 - 05/06] BMW 3 SERIES E46 325Ci COUPE (2.5L 6CYL M54B25 141kW)
- [09/00 - 08/06] BMW 3 SERIES E46 325Ci CONVERTIBLE (2.5L 6CYL M54B25 141kW)
- [09/00 - 04/05] BMW 3 SERIES E46 325i SEDAN (2.5L 6CYL M54B25 141kW)
- [03/02 - 12/04] BMW 3 SERIES E46 325ti COMPACT (2.5L 6CYL M54B25 141kW)
- [06/00 - 05/06] BMW 3 SERIES E46 330Ci COUPE (3.0L 6CYL M54B30 170kW)
- [09/00 - 08/06] BMW 3 SERIES E46 330Ci CONVERTIBLE (3.0L 6CYL M54B30 170kW)
- [09/00 - 02/05] BMW 3 SERIES E46 330i SEDAN (3.0L 6CYL M54B30 170kW)
- [09/00 - 02/05] BMW 3 SERIES E46 330i WAGON (3.0L 6CYL M54B30 170kW)
- [07/00 - 05/06] BMW M3 E46 COUPE (3.2L 6CYL S54B32 252kW)
- [03/01 - 08/06] BMW M3 E46 CONVERTIBLE (3.2L 6CYL S54B32 252kW)
What does an oil level sensor do?
The oil level sensor monitors the volume of engine oil in the sump and alerts the driver when the level drops below a safe threshold. It provides an early warning before oil level drops low enough to affect oil pressure and cause engine damage. Unlike the oil pressure sensor which monitors operating pressure while the engine is running, the oil level sensor typically reads level when the engine is off or at idle and the oil has settled in the sump.
What are the symptoms of a failing oil level sensor?
Common symptoms include an oil level warning light on the dashboard despite the dipstick confirming correct oil level, no warning light appearing even when oil is actually low, and intermittent warnings that appear when the engine is cold and disappear once the engine warms up. A Check Engine light with oil level circuit fault codes may also be present. Always verify actual oil level with the dipstick before assuming the sensor has failed.
How does the oil level sensor work?
Most modern oil level sensors use a thermistor-based measurement system. A heating element warms the sensor tip and the rate at which heat dissipates indicates whether the tip is submerged in oil or exposed to air - oil conducts heat away faster than air. Some older vehicles use a float-based sensor similar to a fuel level sender. The ECU interprets the sensor signal and triggers the warning light when oil level is below the minimum mark.
Can I ignore an oil level warning if my dipstick shows the oil is correct?
A single occurrence of an oil level warning with a correct dipstick reading suggests a faulty sensor. However do not ignore repeated warnings - recheck the dipstick carefully, ensuring the vehicle is on level ground and the engine has been off for at least five minutes to allow oil to drain back into the sump. If the dipstick consistently shows correct level and the warning persists, replace the sensor. If the dipstick shows low oil, top up immediately.
Is the oil level sensor the same as the oil pressure sensor?
No - they are two completely different sensors monitoring different things. The oil level sensor measures the volume of oil in the sump and is a maintenance warning device. The oil pressure sensor measures the pressure of oil circulating through the engine and is a real-time engine protection device. A low oil level will eventually cause low oil pressure, but the level sensor provides an earlier warning. Most vehicles have both sensors fitted separately.
Does replacing the oil level sensor require draining the engine oil?
On most vehicles yes - the oil level sensor is mounted in the oil sump below the oil level, so the engine oil must be drained before the sensor can be removed without spillage. Use this as an opportunity to perform an oil and filter change at the same time, as draining the oil is the main labour component of a service. Refill with the correct grade and quantity of oil specified for your engine after fitting the new sensor.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCPS180 |
| Reference OEM Number | 12617508003 |
| Other OEM Numbers | 12617508003, 12611433596, 12611439810, 12617832375, 13617832205 |
| Related Part Numbers | LS119, OLS1000, CPS180, EPO-BM-000, OPS180 |
| Interchange Part Numbers | V20-72-0462, 6PR007868031, EPO-BM-000, 20923907, 23907, 501522 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Oil Level Sensor |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Fitting Depth | 90 mm |
| Housing Colour | Black |
| Housing Type | Aluminium Housing |
| Number of mounting bores | 3 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.