Oil Level Sensor for BMW E39 540i 535i M5 E38 740i X5 4.4i M62 V8 12617508003
OEM Spec Fit Replaces 12617508003
BRAND NEW *OEM Quality* oil level sensor to suit BMW M62 and S62 V8 engines in the E39, E38 and X5 E53.
A V8 BMW that throws an oil level warning with a full sump needs a new sensor before the warning gets ignored. Stocked in Melbourne and shipped Australia-wide.
TO SUIT
For the BMW E39 540i, 535i and M5 sedan, the E38 740i and 735i including long-wheelbase iL models, and the X5 E53 4.4i and 4.6is. Engines covered are the M62B35, M62B44, M62B46 and the M5's S62B50, 1996-2003.
FITMENT CHECK
On the E39 535i and 540i and the E38 735i and 740i the fit can vary with build date. Before ordering, check the number on your old sensor matches 12617508003 or an OEM number below, and compare the photos with your original part.
OEM PART NUMBERS
- 12617508003
- 12611433596
- 12611439810
- 12617832375
- 13617832205
- 7508003
- 1439810
- 7832205
- 7832375
OTHER PART NUMBERS
- V20-72-0462
- 6PR 007 868-031
- EPO-BM-000
- 20 92 3907
- 23907
- 501 522
- 314 800 0051
- LS119
- OLS1000
- OPS180
PACKAGE INCLUDES
1 x oil level sensor with seal ring, 3-pin D-shaped connector, 3 mounting bolt holes.
ABOUT THIS SENSOR
The sensor mounts in the bottom of the V8 sump and reports oil level and temperature to the cluster and Check Control system.
The M62 runs hot and a failed sensor often reads low or drops out completely, which hides a real oil loss from leaking timing cover or valve cover gaskets.
COMMON SYMPTOMS OF FAILURE
- Check Control message asking you to check the engine oil level when the level is correct
- Low oil level warning that comes and goes after the engine warms up
- No oil level reading in the instrument cluster or on-board computer
- Oil level warning stays on after an oil change or top-up
- Oil weeping from the sensor seal on the bottom of the sump
- [10/96 - 08/98] BMW 5 SERIES E39 535i SEDAN (3.5L V8 M62B35 173kW)
- [10/96 - 06/03] BMW 5 SERIES E39 540i SEDAN (4.4L V8 M62B44 210kW)
- [03/99 - 06/03] BMW M5 E39 SEDAN (4.9L V8 S62B50 294kW)
- [03/96 - 08/98] BMW 7 SERIES E38 735i 735iL (3.5L V8 M62B35 173kW)
- [07/96 - 07/01] BMW 7 SERIES E38 740i 740iL (4.4L V8 M62B44 210kW)
- [01/01 - 09/03] BMW X5 E53 4.4i (4.4L V8 M62B44 210kW)
- [10/01 - 09/03] BMW X5 E53 4.6is (4.6L V8 M62B46 255kW)
- IMPORTANT FITMENT NOTE: E39 535i 540i and E38 735i 740i - fit can vary with build date. Check your OEM number and compare the photos with your original part
What does an oil level sensor do?
The oil level sensor monitors the volume of engine oil in the sump and alerts the driver when the level drops below a safe threshold. It provides an early warning before oil level drops low enough to affect oil pressure and cause engine damage. Unlike the oil pressure sensor which monitors operating pressure while the engine is running, the oil level sensor typically reads level when the engine is off or at idle and the oil has settled in the sump.
What are the symptoms of a failing oil level sensor?
Common symptoms include an oil level warning light on the dashboard despite the dipstick confirming correct oil level, no warning light appearing even when oil is actually low, and intermittent warnings that appear when the engine is cold and disappear once the engine warms up. A Check Engine light with oil level circuit fault codes may also be present. Always verify actual oil level with the dipstick before assuming the sensor has failed.
How does the oil level sensor work?
Most modern oil level sensors use a thermistor-based measurement system. A heating element warms the sensor tip and the rate at which heat dissipates indicates whether the tip is submerged in oil or exposed to air - oil conducts heat away faster than air. Some older vehicles use a float-based sensor similar to a fuel level sender. The ECU interprets the sensor signal and triggers the warning light when oil level is below the minimum mark.
Can I ignore an oil level warning if my dipstick shows the oil is correct?
A single occurrence of an oil level warning with a correct dipstick reading suggests a faulty sensor. However do not ignore repeated warnings - recheck the dipstick carefully, ensuring the vehicle is on level ground and the engine has been off for at least five minutes to allow oil to drain back into the sump. If the dipstick consistently shows correct level and the warning persists, replace the sensor. If the dipstick shows low oil, top up immediately.
Is the oil level sensor the same as the oil pressure sensor?
No - they are two completely different sensors monitoring different things. The oil level sensor measures the volume of oil in the sump and is a maintenance warning device. The oil pressure sensor measures the pressure of oil circulating through the engine and is a real-time engine protection device. A low oil level will eventually cause low oil pressure, but the level sensor provides an earlier warning. Most vehicles have both sensors fitted separately.
Does replacing the oil level sensor require draining the engine oil?
On most vehicles yes - the oil level sensor is mounted in the oil sump below the oil level, so the engine oil must be drained before the sensor can be removed without spillage. Use this as an opportunity to perform an oil and filter change at the same time, as draining the oil is the main labour component of a service. Refill with the correct grade and quantity of oil specified for your engine after fitting the new sensor.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCPS180 |
| Reference OEM Number | 12617508003 |
| Other OEM Numbers | 12617508003, 12611433596, 12611439810, 12617832375, 13617832205 |
| Related Part Numbers | LS119, OLS1000, CPS180, EPO-BM-000, OPS180 |
| Interchange Part Numbers | V20-72-0462, 6PR007868031, EPO-BM-000, 20923907, 23907, 501522 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Oil Level Sensor |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Fitting Depth | 90 mm |
| Housing Colour | Black |
| Housing Type | Aluminium Housing |
| Number of mounting bores | 3 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | E38/E39 V8: check OEM no and compare photos with your old part |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.