Oil Level Sensor for BMW X1 E84 sDrive20i xDrive28i Z4 E89 N20 12617501786
OEM Spec Fit Replaces 12617501786
BRAND NEW *OEM Quality* oil level sensor to suit the BMW X1 E84 and Z4 E89 petrol four-cylinder.
An oil level warning on an X1 or Z4 with oil on the dipstick usually means the sump sensor has failed. Stocked in Melbourne and shipped Australia-wide.
TO SUIT
For the BMW X1 E84 sDrive20i and xDrive28i with the N20B20 turbo engine (2011-2015) and the sDrive18i (2010-2015). It also suits the Z4 E89 roadster sDrive20i and sDrive28i with the N20, 2011-2016.
OEM PART NUMBERS
- 12617501786
- 7501786
OTHER PART NUMBERS
- V20-72-0468
- 6PR 008 324-101
- 7.13500.01.0
- EPO-BM-001
- 20 92 6154
- 26154
- 501 521
- 314 899 0028
- LS121
- OLS1012
- OPS169
PACKAGE INCLUDES
1 x oil level sensor with seal ring, 3-pin D-shaped connector, 3 mounting bolt holes.
ABOUT THIS SENSOR
The sensor mounts in the bottom of the sump and gives the electronic oil level reading shown in the iDrive or cluster - the N20 has no dipstick, so on those cars it is the only way to check the oil.
The N20 turbo is sensitive to low oil, so a sensor that reads wrong or drops out puts the turbo and timing chain at risk without warning.
COMMON SYMPTOMS OF FAILURE
- Check Control message asking you to check the engine oil level when the level is correct
- Low oil level warning that comes and goes after the engine warms up
- No oil level reading in the instrument cluster or on-board computer
- Oil level warning stays on after an oil change or top-up
- Oil weeping from the sensor seal on the bottom of the sump
- [01/10 - 06/15] BMW X1 E84 sDrive18i (2.0L 4CYL 110kW)
- [09/11 - 06/15] BMW X1 E84 sDrive20i (2.0L 4CYL TURBO N20B20 135kW)
- [03/11 - 06/15] BMW X1 E84 xDrive28i (2.0L 4CYL TURBO N20B20 180kW)
- [09/11 - 08/16] BMW Z4 E89 sDrive20i ROADSTER (2.0L 4CYL TURBO N20B20 135kW)
- [09/11 - 08/16] BMW Z4 E89 sDrive28i ROADSTER (2.0L 4CYL TURBO N20B20 180kW)
What does an oil level sensor do?
The oil level sensor monitors the volume of engine oil in the sump and alerts the driver when the level drops below a safe threshold. It provides an early warning before oil level drops low enough to affect oil pressure and cause engine damage. Unlike the oil pressure sensor which monitors operating pressure while the engine is running, the oil level sensor typically reads level when the engine is off or at idle and the oil has settled in the sump.
What are the symptoms of a failing oil level sensor?
Common symptoms include an oil level warning light on the dashboard despite the dipstick confirming correct oil level, no warning light appearing even when oil is actually low, and intermittent warnings that appear when the engine is cold and disappear once the engine warms up. A Check Engine light with oil level circuit fault codes may also be present. Always verify actual oil level with the dipstick before assuming the sensor has failed.
How does the oil level sensor work?
Most modern oil level sensors use a thermistor-based measurement system. A heating element warms the sensor tip and the rate at which heat dissipates indicates whether the tip is submerged in oil or exposed to air - oil conducts heat away faster than air. Some older vehicles use a float-based sensor similar to a fuel level sender. The ECU interprets the sensor signal and triggers the warning light when oil level is below the minimum mark.
Can I ignore an oil level warning if my dipstick shows the oil is correct?
A single occurrence of an oil level warning with a correct dipstick reading suggests a faulty sensor. However do not ignore repeated warnings - recheck the dipstick carefully, ensuring the vehicle is on level ground and the engine has been off for at least five minutes to allow oil to drain back into the sump. If the dipstick consistently shows correct level and the warning persists, replace the sensor. If the dipstick shows low oil, top up immediately.
Is the oil level sensor the same as the oil pressure sensor?
No - they are two completely different sensors monitoring different things. The oil level sensor measures the volume of oil in the sump and is a maintenance warning device. The oil pressure sensor measures the pressure of oil circulating through the engine and is a real-time engine protection device. A low oil level will eventually cause low oil pressure, but the level sensor provides an earlier warning. Most vehicles have both sensors fitted separately.
Does replacing the oil level sensor require draining the engine oil?
On most vehicles yes - the oil level sensor is mounted in the oil sump below the oil level, so the engine oil must be drained before the sensor can be removed without spillage. Use this as an opportunity to perform an oil and filter change at the same time, as draining the oil is the main labour component of a service. Refill with the correct grade and quantity of oil specified for your engine after fitting the new sensor.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCPS169 |
| Reference OEM Number | 12617501786 |
| Other OEM Numbers | 12617501786, 7501786 |
| Related Part Numbers | CPS169, LS121, 6PR008324-101, EPO-BM-001, OLS1012, OPS169 |
| Interchange Part Numbers | V20-72-0468, 6PR008324-101, 7.13500.01.0, EPO-BM-001, 20926154 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Oil Level Sensor |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Fitting Depth | 82 mm |
| Number of mounting bores | 3 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.