Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2 Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2

Intake Camshaft Sensor for BMW E39 M5 E52 Z8 S62 V8 Bank 1 or 2

Part #: CSCA122 OEM #: 12147518628 SKU: CSCA122_2

OEM Spec Fit for BMW S62 V8 Bank 1 or 2

$78.97
RRP $162.03
SAVE $83.06 (51%)
In Stock

BRAND NEW *OEM Quality* Intake Camshaft Position Sensor to suit BMW's S62 5.0L V8 engine.

If your M5 or Z8 is running rough, hesitating, or throwing a cam sensor fault code, this is a common fix for the S62 V8. Same-day dispatch from Melbourne.

TO SUIT

This sensor suits the BMW E39 M5 and E52 Z8, both fitted with the 5.0L S62 V8 engine, built from 2000 to 2003. It fits either Bank 1 or Bank 2 - the same part is used on both sides.

FITMENT CHECK

This is the intake-side sensor for the S62 V8 only. It is not interchangeable with the N42/N46/N52/N54 exhaust-side sensor used on other BMW models. Please confirm your engine code is S62 before ordering.

OEM PART NUMBERS

  • 12147518628
  • 12147506273
  • 12141435351
  • 12141438082

PACKAGE INCLUDES

1 x 'OEM Quality' Intake Camshaft Position Sensor (3-pin plug). Suits Bank 1 or Bank 2 of the S62 V8 engine.

ABOUT THIS SENSOR

The camshaft position sensor works with the crankshaft sensor to tell the engine control unit exactly where each cylinder is in its cycle.

When it fails, the ECU loses accurate timing data, which can cause rough running, reduced power, a check engine light or a no-start condition.

COMMON SYMPTOMS OF FAILURE

  • Check engine light with fault code P0341 or P0345
  • Rough idle or hesitation on acceleration
  • Reduced engine power or limp mode
  • Engine cranks but will not start
  • Intermittent stalling at idle
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA122_2
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCSCA122
Reference OEM Number12147518628
Other OEM Numbers12147518628, 12147506273, 12141435351, 12141438082
Related Part NumbersCAM-063, TCAS261, SC381, SS10888
Trade Part NumbersV20-72-9001, 235-1214
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Fitting PositionExhaust Side
Number of pins3 -pin connector
Connector ShapeD-shaped
Supplementary Article Infofor camshaft, without cable, with seal ring
Fitting Depth28 mm
Rated Voltage12 V
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category