Crankshaft Position Sensor for BMW N62 V8 540i 545i 550i 645Ci 650i 745i 750i Crankshaft Position Sensor for BMW N62 V8 540i 545i 550i 645Ci 650i 745i 750i Crankshaft Position Sensor for BMW N62 V8 540i 545i 550i 645Ci 650i 745i 750i Crankshaft Position Sensor for BMW N62 V8 540i 545i 550i 645Ci 650i 745i 750i

Crankshaft Position Sensor for BMW N62 V8 540i 545i 550i 645Ci 650i 745i 750i

Part #: SCSCA142 Replaces OEM: 13627548994

OEM Spec Fit Replaces 13627548994

$93.67
RRP $157.99
SAVE $64.32 (41%)
In Stock

BRAND NEW *OEM Quality* crankshaft position sensor to suit BMW 5 6 and 7 Series V8.

Is your 745i or 650i cranking without firing or cutting out at speed with a crank sensor code? This sensor brings the V8 back to life - dispatched from Victoria same-day before 12pm.

TO SUIT

Fits the N62 V8 in the BMW E60 540i 545i and 550i, E63 and E64 645Ci and 650i, and E65 E66 735i 740i 745i and 750i. It is also listed for the 760i V12, the earlier E38 740i M62 and the Rolls Royce Phantom.

FITMENT CHECK

Our supplier data flags some N62 cars built from 2005 for a photo check. Compare your old sensor or the OEM number on it before ordering.

OEM PART NUMBERS

  • 13627548994
  • 12147503140
  • 7548994
  • 7503140

OTHER PART NUMBERS

  • CHN3-V293
  • SS11074
  • V20-72-9002

PACKAGE INCLUDES

1 x BRAND NEW crankshaft position sensor with 3-pin D-shaped connector.

ABOUT THIS SENSOR

On the N62 the crank sensor works with the cam sensors to sequence all eight cylinders. If the crank signal is lost the DME has no reference at all and the engine stops.

Failure is usually heat related - a hot V8 that stalls and will not restart until it cools is a classic sign. Some cars also show a jumpy rev counter first.

COMMON SYMPTOMS OF FAILURE

  • Stalls when hot and will not restart
  • Crank no-start
  • Engine light with codes P0335 P0336 or P0339
  • Rev counter jumping or dropping to zero
  • Misfire under load
  • [2003 - 2005] BMW 5 SERIES E60 SEDAN 545i (4.4L V8 N62 B44 A 245kW) RWD - built to 12/06
  • [2005 - 2009] BMW 5 SERIES E60 SEDAN 550i (4.8L V8 N62 B48 B 270kW) RWD
  • [2007 - 2009] BMW 5 SERIES E60 SEDAN 540i (4.0L V8 N62 B40 A 225kW) RWD
  • [2003 - 2009] BMW 6 SERIES E63 COUPE 645Ci (4.4L V8 N62 B44 A 245kW) RWD - built to 12/06
  • [2004 - 2009] BMW 6 SERIES E64 CONVERTIBLE 645Ci (4.4L V8 N62 B44 A 245kW) RWD - built to 12/06
  • [2005 - 2009] BMW 6 SERIES E63 COUPE 650i (4.8L V8 N62 B48 B 270kW) RWD - built to 06/06
  • [2005 - 2009] BMW 6 SERIES E64 CONVERTIBLE 650i (4.8L V8 N62 B48 B 270kW) RWD - built to 06/06
  • [1996 - 2001] BMW 7 SERIES E38 SEDAN 740i/iL (4.4L V8 M62 B44 (448S1)/ M62 B44 (448S2) 210kW) RWD
  • [2002 - 2005] BMW 7 SERIES E66/E65/E67 SEDAN 735i/Li (3.6L V8 N62 B36 A 200kW) RWD
  • [2002 - 2005] BMW 7 SERIES E66/E65/E67 SEDAN 745i/Li (4.4L V8 N62 B44 A 245kW) RWD - built to 12/06
  • [2003 - 2008] BMW 7 SERIES E66/E65/E67 SEDAN 760i/Li (6.0L V12 N73 B60 A/ N73 B60 B 327kW) RWD
  • [2005 - 2005] BMW 7 SERIES E66/E65/E67 SEDAN 740i/Li (4.0L V8 N62 B40 A 225kW) RWD - built to 06/06
  • [2005 - 2005] BMW 7 SERIES E66/E65/E67 SEDAN 750i/Li (4.8L V8 N62 B48 B 270kW) RWD
  • [2003 - 2017] ROLLS ROYCE PHANTOM RR1 SEDAN V12 (6.8L V12 N73 B68 A 338kW) RWD
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
BrandAftermarket OEM Replacement
Part Numbers
Part NumberSCSCA142
Reference OEM Number13627548994
Other OEM Numbers13627548994, 12147503140, 7548994, 7503140
Related Part NumbersCAS-206, SC359, TCAS302, CSCA142
Interchange Part NumbersCHN3-V293, SS11074, V20-72-9002
Product Specifics
Product TypeSENSOR
Sensor TypeCRANKSHAFT POSITION SENSOR
Manufacturer Warranty1 Year
Number of pins3-Pin
Connector ShapeD-shaped
Fitting Depth28mm
Housing ColourBlack
Length65mm
Compatible MakesBMW
Fitment TypeDirect Replacement
Other Details
NoteN62 cars built 2005 on - check your old sensor or OEM number
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category