Crank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5L Crank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5LCrank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5L

Crank Angle Sensor 9091905005 for Toyota Hilux LN KZN Surf 1KZ-TE 5L

Part #: CSCA150 OEM #: 90919-05005 SKU: CSCA150-Hilux

Heavy Duty Fit Replaces 9091905005

$98.97
RRP $159.99
SAVE $61.02 (38%)
In Stock

BRAND NEW *OEM Quality* crank angle sensor to suit Toyota Hilux LN and KZN series diesel - 5L-E 3.0L and 1KZ-TE 3.0L engines.

A failed crank angle sensor on these Hilux models causes no-start or stalling conditions as the ECU loses crankshaft position data. This is a direct plug-and-play replacement - same 2-pin oval connector - packed and shipped express from Cranbourne VIC.

TO SUIT

Suits Toyota Hilux LN147 / LN152 / LN167 / LN172 with the 5L and 5L-E 3.0L diesel engine from 1997-2005. Also fits the Hilux KZN165 and Hilux Surf KZN130 / KZN185 with the 1KZ-TE 3.0L turbo diesel - and Hilux Surf LN130 with the 2L-T / 2L-TE 2.4L engine.

OEM PART NUMBERS

  • 9091905005
  • 9091905063
  • 90919-05005

OTHER PART NUMBERS

  • BOSCH: 0 986 280 808
  • NTY: ECP-TY-015
  • VEMO: V70-72-0129

PACKAGE INCLUDES

1 x crank angle sensor with 2-pin oval connector - without cable.

ABOUT THIS SENSOR

The crank angle sensor monitors crankshaft position and speed on the 5L-E and 1KZ-TE diesel engines and feeds this data to the ECU for fuel injection timing. On the 1KZ-TE in particular it is a common failure point - the sensor sits in a heat-exposed location and the signal wire insulation degrades over time.

Failure on these engines typically produces a hard no-start or sudden stall at operating temperature - the engine may crank but will not fire as the ECU cannot determine injection timing without the crank signal.

COMMON SYMPTOMS OF FAILURE

  • Engine cranks but will not start - especially when warm
  • Sudden stall at idle or low speed
  • Intermittent stalling that clears when engine cools
  • Check engine light - fault codes P0335 / P0336
  • Rough idle or misfiring under load
  • Loss of power or hesitation on acceleration
  • [08/93 - 10/95] TOYOTA HILUX SURF KZN130 II TDi 3.0L 4cyl 1KZ-TE 96kW
  • [12/95 - 07/98] TOYOTA HILUX SURF KZN185 III TDi 3.0L 4cyl 1KZ-TE 96kW
  • [08/98 - 06/00] TOYOTA HILUX SURF KZN185 III TDi 3.0L 4cyl 1KZ-TE 108kW
  •  
  • [04/89 - 07/90] TOYOTA HILUX SURF LN130 II TD 2.4L 4cyl 2L-T 66kW
  • [08/90 - 07/93] TOYOTA HILUX SURF LN130 II TDi 2.4L 4cyl 2L-TE 71kW
  •  
  • [08/97 - 08/00] TOYOTA HILUX LN147/LN152 VI D 3.0L 4cyl 5L 65kW
  • [09/00 - 04/05] TOYOTA HILUX LN147 VI D 3.0L 4cyl 5L-E 71kW
  • [09/00 - 04/05] TOYOTA HILUX LN152 VI D 3.0L 4cyl 5L-E 71kW
  • [08/97 - 08/05] TOYOTA HILUX LN167/LN172 VI D 3.0L 4cyl 5L-E 71kW
  •  
  • [08/93 - 04/05] TOYOTA HILUX KZN165 VI TDi 3.0L 4cyl 1KZ-TE 85kW
  • [1999 - 2000] TOYOTA HILUX SR5 KZN165 TDi 3.0L 4cyl 1KZ-TE 85kW
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA150-Hilux
Barcode #9314258113629
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCSCA150
Reference OEM Number90919-05005
Other OEM Numbers9091905005, 9091905063, 90919-05005
Related Part NumbersCAS-223, CSCA150, SC400, CAS1229
Trade Part NumbersBOSCH: 0 986 280 808, NTY: ECP-TY-015, VEMO: V70-72-0129
Product Specifics
Product TypeSENSOR
Sensor TypeCRANKSHAFT POSITION SENSOR
Number of pins2-Pin
Connector Shapeoval
Housing ColourBlack
Compatible MakesToyota
Fitment TypeDirect Replacement
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category