Crank and Cam Angle Sensor for Nissan Navara D22 D40 Pathfinder R51 2.5L YD25
Workshop Grade Replaces 23731-EC00A
BRAND NEW *OEM Quality* crank and cam angle sensor pair to suit the Nissan Navara and Pathfinder with the YD25 2.5L turbo diesel.
Replacing both sensors together makes sense when one has failed on a high-kilometre YD25, and it saves pulling things apart twice. Both units are packed together and dispatched same day before 12pm from Melbourne.
TO SUIT
Nissan Navara D40 and Pathfinder R51 with the YD25DDTi 2.5L diesel from 2005 on, plus the late Navara D22 YD25DDT. On the YD25 the same part number is used in both the camshaft and crankshaft positions.
FITMENT CHECK
- On the Navara D40 and Pathfinder R51 this part suits both Spanish-built (VIN starting VSK) and Thai-built (VIN starting MNT) vehicles with the YD25 engine.
- Navara D22 built before 06/2008 uses this part in the camshaft position; from 06/2008 it is the crankshaft sensor.
- Before ordering check that your old sensor carries one of the OEM numbers listed below.
OEM PART NUMBERS
- 23731-EC00A
- 23731-AW410
- 23731-EC01A
- 23731ED01A
OTHER PART NUMBERS
- 6PU009168-331
- SS11155
- V38-72-0202
PACKAGE INCLUDES
2 x crank and cam angle sensor, each with a 3-pin oval connector, seal ring and single bolt-hole mount.
ABOUT THIS SENSOR
The YD25 relies on two position signals: the crank sensor tracks crankshaft speed and position, and the cam sensor tells the ECU which stroke each cylinder is on. The common-rail system needs both to sequence injection, so a fault in either one can stop the engine.
Both sensors live with the same heat and vibration and age at a similar rate, which is why workshops often replace them as a pair on Navara and Pathfinder diesels.
COMMON SYMPTOMS OF FAILURE
- No start or long cranking
- Stalling once hot
- Fault code P0335 crankshaft position sensor
- Fault code P0340 camshaft position sensor
- Limp mode or loss of power
- Check engine light on
- [02/02 - 02/15] NISSAN NAVARA D22 2.5L YD25DDTi 98kW Utility/Cab Chassis 2WD/4WD - camshaft position
- [06/08 - 02/15] NISSAN NAVARA D22 2.5L YD25DDTi 98kW Utility/Cab Chassis 2WD/4WD - crankshaft position (built from 06/2008)
- [12/05 - 01/13] NISSAN NAVARA D40 2.5L YD25DDTi 128kW Utility 4WD
- [01/07 - 10/15] NISSAN NAVARA D40 2.5L YD25DDTi 126kW Utility 4WD
- [08/08 - 10/15] NISSAN NAVARA D40 2.5L YD25DDTi 126kW Cab Chassis 4WD
- [07/08 - 04/15] NISSAN NAVARA D40 2.5L YD25DDTi 106kW Cab Chassis 4WD
- [11/09 - 10/15] NISSAN NAVARA D40 2.5L YD25DDTi 106kW Utility 2WD
- [05/10 - 04/15] NISSAN NAVARA D40 2.5L YD25DDTi 120kW Utility 2WD
- [05/10 - 04/15] NISSAN NAVARA D40T 2.5L YD25DDTi 140kW Utility 4WD
- [06/12 ON] NISSAN NV350 E26 2.5L YD25DDTi 95kW Van
- [07/05 - 10/13] NISSAN PATHFINDER R51 2.5L YD25DDTi 128kW 4WD
- [08/10 - 12/13] NISSAN PATHFINDER R51 2.5L YD25DDTi 140kW 4WD
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA132-PAIR |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CSCA132-PAIR |
| Reference OEM Number | 23731-EC00A |
| Other OEM Numbers | 23731-AW410, 23731-EC00A, 23731-EC01A, 23731ED01A |
| Related Part Numbers | CAS-222, CMN2-V450, SC408, TCAS199 |
| Trade Part Numbers | 6PU009168-331, SS11155, V38-72-0202 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CRANKSHAFT POSITION SENSOR |
| Manufacturer Warranty | 1 Year |
| Ean | 9341554033580 |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Supplementary Article Info | without cable, with seal ring |
| Fitting Depth | 56 mm |
| Rated Voltage | 12 V |
| Housing Colour | Black |
| Number of Bolt Holes | 1 |
| Mounting Type | Bolted |
| Fitment Type | Direct Replacement |
| Kit Quantity | 2 |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.