





Camshaft Sensor for Hyundai i30 i40 ix35 Tucson 3935023910
Direct Fit Replaces 39350-23910
BRAND NEW *OEM Quality* Camshaft Position Sensor to suit Hyundai i30, i40, ix35, Tucson 1.8L 2.0L petrol engines.
If your check engine light is on or your car is stalling unexpectedly while driving - a failing camshaft sensor loses sync with the ECU under heat and cuts fuel injector timing. Ships daily from our Cranbourne VIC warehouse.
TO SUIT
This sensor suits the Hyundai i30 FD GD (2007-2017) with 1.8L and 2.0L petrol engines, i40 VF (2011-2021) 2.0L, ix35 LM (2013-2015) 2.0L GDi, and Tucson JM TL (2004-2021) 2.0L. 3-pin connector.
OEM PART NUMBERS
- 39350-23910
- 3935023910
- 39350-23700
- 3935023700
OTHER PART NUMBERS
- VEMO: V53-72-0116
- WALKER: 235-1273
PACKAGE INCLUDES
1 x Camshaft Position Sensor - 3-pin connector, supplied without cable, with seal ring.
ABOUT THIS SENSOR
The camshaft sensor works with the crankshaft sensor to tell the ECU the exact position of the camshaft relative to the crankshaft, so it knows when each cylinder reaches top dead centre.
When the sensor fails or drifts out of tolerance from heat exposure, the ECU loses accurate cylinder timing - this can cause hard starting, rough idle, misfires, and sudden stalling.
COMMON SYMPTOMS OF FAILURE
- Difficulty starting the vehicle
- Intermittent stalling while driving
- Check engine light - camshaft position fault codes
- Uneven acceleration
- Engine misfires or vibrates
- Rough idle
- [2007-2017] HYUNDAI i30 FD GD 1.8L 2.0L Petrol
- [2011-2021] HYUNDAI i40 VF 2.0L Petrol
- [2013-2015] HYUNDAI ix35 LM 2.0L GDi Petrol
- [2004-2021] HYUNDAI TUCSON JM TL 2.0L Petrol
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | 3935023910 |
| Brand | OEM |
| Part Numbers | |
| Part Number | 3935023910 |
| Reference OEM Number | 39350-23910 |
| Other OEM Numbers | 3935023910, 3935023700, 39350-23700, 39350-23910 |
| Related Part Numbers | EC0289, SS11353, CSCA116, CSCA395, SC239 |
| Trade Part Numbers | VEMO: V53-72-0116, WALKER: 235-1273 |
| Product Specifics | |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Type | Sensor |
| Features | Direct Fit |
| Manufacturer Warranty | 1 Year |
| Number of pins | 3 -pin connector |
| Connector Shape | rectangular |
| Supplementary Article Info | without cable, with seal ring |
| Fitting Depth | 28.2 mm |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.