Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40 Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40

Camshaft Position Sensor RH for Nissan Navara D40 Pathfinder R51 VQ40

Part #: CSCA514 OEM #: 23731-6J906 SKU: CSCA514-1

Heavy Duty Fit Replaces 23731-6J906

$87.99
RRP $149.99
SAVE $62.00 (41%)
In Stock

BRAND NEW *OEM Quality* right hand exhaust side camshaft position sensor to suit Nissan Navara D40 and Pathfinder R51 4.0L VQ40DE.

A VQ40 that cranks and cranks without firing is the classic dead cam sensor - this is the direct replacement and it is stocked in Melbourne.

TO SUIT

Suits the Navara D40 ute with the 4.0L VQ40 petrol V6 built from 01/2006 onward and the Pathfinder R51 wagon with the VQ40DE from 09/2005. Both are the petrol V6 only - the YD25 turbo diesel Navara and Pathfinder do not use this sensor.

FITMENT CHECK

Petrol VQ40 V6 only - not the YD25 diesel. This is the RIGHT HAND exhaust side sensor with a straight plug. The left bank takes our CSCA524. Navara D40 built before 01/2006 uses an earlier sensor.

OEM PART NUMBERS

  • 23731-6J906
  • 23731-6J900
  • 23731-6J902
  • 23731-6J905
  • 23731-6J90A
  • 23731-6J90B
  • 23731-6J90C
  • 23731-6J90D
  • 23731-6J960
  • 23731-6J966
  • 23731-6J96B
  • 23731-5M010
  • 23731-5M015
  • 23731-5M016

OTHER PART NUMBERS

  • BOSCH: 0 986 JG1 628
  • VEMO: V38-72-0128
  • NTK-AU: EC0238
  • HELLA: 6PU 013 122-661
  • ASHIKA: 152-01-100
  • WALKER PRODUCTS: 235-1152

PACKAGE INCLUDES

1 x camshaft position sensor with straight oval 3-pin connector. Direct plug-in fit to the D40 and R51 factory harness.

ABOUT THIS SENSOR

On the VQ40 the right hand cam sensor sits high on the exhaust side of the head where under-bonnet heat is worst, and these utes and wagons spend their life at sustained load towing or loaded. That duty cycle is what shortens the sensor's life compared to the same part in a passenger car.

When it fails the ECU loses cam phase and cannot sequence injection. On a D40 that usually shows as extended cranking that gets worse over weeks until the ute will not start at all.

COMMON SYMPTOMS OF FAILURE

  • Extended cranking that worsens over time then no start
  • Check engine light with P0340 or P0345 stored
  • Stalling when hot or when idling after a tow
  • Rough idle and misfire under load or on hills
  • Loss of power and limp mode on the highway
  • Erratic or surging idle speed
  • [01/06 - 06/11] NISSAN NAVARA D40 (4.0L V6 VQ40 198kW)
  •  
  • [09/05 - 12/13] NISSAN PATHFINDER R51 III (4.0L V6 VQ40DE 198kW)
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA514-1
Barcode #9341554096110
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCSCA514
Reference OEM Number23731-6J906
Other OEM Numbers23731-6J906, 23731-6J90A, 23731-6J90B, 23731-6J90C, 23731-5M015
Related Part Numbers0986JG1628, CAM-075, SC268, CSCA514
Trade Part NumbersBOSCH: 0 986 JG1 628, VEMO: V38-72-0128, NTK-AU: EC0238
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Fitting PositionRight Hand Side Exhaust
Number of pins3-Pin
Connector Shapeoval
Supplementary Article Infowithout cable
Fitting Depth37.8 mm
Rated Voltage12 V
Housing ColourBlack
Compatible MakesNissan
Fitment TypeDirect Replacement
Other Details
NoteRHS exhaust side sensor. Straight plug. LH side is CSCA524.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category