







Camshaft Position Sensor for Fiat Ducato 250 290 2.8 3.0 JTD 504048261
Workshop Grade Replaces 504048261
BRAND NEW *OEM Quality* camshaft position sensor to suit Fiat Ducato 2.8 JTD and 3.0 Multijet engines.
In a Ducato this fault often presents as a stall coming off the throttle at a roundabout, with the engine light appearing only after the third or fourth occurrence. This is a direct replacement backed by our returns policy.
TO SUIT
Fits the Fiat Ducato 230 and 244 series 2.8 JTD and 2.8 TD on the 8140.43S engine, and the 250 and 290 series 3.0 Multijet in 150, 160 and 180 outputs running F1CE0481D, F1CE3481E, F1CE3481M and F1CE3481N. Covers van, bus and platform chassis bodies.
FITMENT CHECK
The 244 series changed sensor supplier partway through production. Check the number on the old sensor and confirm the connector is a 3-pin oval with 24.2mm body depth before ordering.
OEM PART NUMBERS
- 504048261
- 55187973
- 46798367
- 46798369
- 112685
OTHER PART NUMBERS
- BOSCH: 0281002904
- VALEO: 253804
- FAE: 79350
- ASHIKA: 152-0K-K06
- DT Spare Parts: 7.51415
PACKAGE INCLUDES
1 x camshaft position sensor with 3-pin oval connector and seal ring. Supplied without cable.
ABOUT THIS SENSOR
The camshaft position sensor establishes cylinder phase so the Ducato ECU can sequence the common rail injectors correctly. Without it the ECU can still run the engine from the crank signal alone, but only in a degraded batch-fire mode.
That fallback is why a Ducato with a dying cam sensor usually still drives. You get poor fuel economy, a lazy throttle and a stall on deceleration rather than an outright breakdown, so the fault can go unresolved for months.
COMMON SYMPTOMS OF FAILURE
- Stalling as you come off the throttle at low speed
- P0340 P0341 or P0016 stored in the ECU
- Long crank before the engine fires
- Noticeably worse fuel consumption than usual
- Flat throttle response with the vehicle unladen
- Engine light appearing and clearing intermittently
- [2000 - 2002] FIAT DUCATO 230 Platform/Chassis 2.8 JTD (2.8L 4cyl 94kW 8140.43S Diesel FWD)
- [2001 - 2007] FIAT DUCATO 244 Bus 2.8 JTD (2.8L 4cyl 94kW 8140.43S Diesel FWD)
- [2001 - 2006] FIAT DUCATO 244 Platform/Chassis 2.8 JTD (2.8L 4cyl 94kW 8140.43S Diesel FWD)
- [2001 - 2014] FIAT DUCATO 244 Van 2.8 JTD (2.8L 4cyl 94kW 8140.43S Diesel FWD)
- [2001 - 2006] FIAT DUCATO 244 Van 2.8 TD (2.8L 4cyl 90kW 8140.43 Diesel FWD)
- [2006 - 2011] FIAT DUCATO 250 Van 160 Multijet 3.0 D (3.0L 4cyl 115kW F1CE3481M Diesel FWD)
- [2010 - 2023] FIAT DUCATO 250 Van 150 Multijet 3.0 D (3.0L 4cyl 107kW F1CE3481N Diesel FWD)
- [2006 - 2016] FIAT DUCATO 250,290 Van 160 Multijet 3.0 D (3.0L 4cyl 116kW F1CE0481D Diesel FWD)
- [2011 - 2016] FIAT DUCATO 250,290 Van 180 Multijet 3.0 D (3.0L 4cyl 130kW F1CE3481E Diesel FWD)
- [2011 - 2016] FIAT DUCATO 250,290 Platform/Chassis 180 Multijet 3.0 D (3.0L 4cyl 130kW F1CE3481E Diesel FWD)
- [2017 - 2021] FIAT DUCATO 250,290 Van 180 Multijet 3.0 D (3.0L 4cyl 130kW F1CE3481E Diesel FWD)
- [2017 - 2021] FIAT DUCATO 250,290 Platform/Chassis 180 Multijet 3.0 D (3.0L 4cyl 130kW F1CE3481E Diesel FWD)
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA329-5 |
| Barcode # | 3165144045229 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CSCA329 |
| Reference OEM Number | 504048261 |
| Other OEM Numbers | 504048261, 55187973, 46798367, 46798369 |
| Related Part Numbers | 0281002904, 39300-27400, 3930027400, CSCA329 |
| Trade Part Numbers | BOSCH: 0281002904, VALEO: 253804, FAE: 79350, ASHIKA: 152-0K-K06 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Fitting Position | Fits On Cylinder Head |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Number of connectors | 1 |
| Housing Colour | Black |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Suits 24.2mm depth 3-pin oval sensor - not the 24.5mm type |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.