This throttle position sensor is a direct-fit replacement for Toyota Land Cruiser Prado VZJ90 and VZJ95 with the 3.4L V6 5VZ-FE engine. It replaces OEM number 89452-35020 - same 3-pin rectangular housing, same anticlockwise rotation, same calibration as the original unit.

The VZJ Prado V6 is a capable touring and family four-wheel drive. When the TPS signal degrades, the ECU loses its reference for throttle position - producing uneven idle, hesitation under acceleration, and unpredictable response during low-range off-road use. Replacing the sensor early restores full ECU authority and smooth, responsive driving.

TO SUIT

This sensor is the correct fit for the Toyota Land Cruiser Prado VZJ90 and VZJ95, built 07/96 - 02/03 with the 3.4L V6 5VZ-FE engine producing 131kW.

FITMENT CHECK

This listing covers the 3.4L V6 5VZ-FE Prado VZJ90 and VZJ95 only. The 2.7L 3RZ-FE Prado RZJ series is covered by a separate listing. Diesel Prado variants do not use this sensor. Replaces OEM numbers 89452-35020 and 89452-35100.

OEM PART NUMBERS

Toyota: 89452-35020
Toyota: 89452-35100

OTHER PART NUMBERS

VEMO: V70-72-0255
WALKER: 200-1238
SensorGal: CTPS192

PACKAGE INCLUDES

1 x Throttle Position Sensor

ABOUT THIS SENSOR

3-pin rectangular connector. Anticlockwise rotation. Supplied without cable. 2 mounting bores. Calibrated to the OEM resistance specification for Toyota 89452-35020 across the full throttle sweep of the 3.4L V6 5VZ-FE.

The VZJ Prado's V6 delivers a wider torque spread than the 4-cylinder RZJ, and a degraded TPS signal here shows up first as an uneven idle or a flat spot right off idle before the V6 picks up cleanly.

COMMON SYMPTOMS OF FAILURE

Rough idle that varies with throttle position
Hesitation or flat spot when accelerating from rest
Surge or hunting at highway speed
Poor fuel economy with no other fault
Transmission hunting between gears on auto models
Check engine light - fault codes P0120, P0121, P0122, P0123

[07/96 - 02/03] TOYOTA LAND CRUISER PRADO VZJ90/ VZJ95 3.4L V6 5VZ-FE 131kW

What fault codes does a faulty TPS trigger?

A faulty throttle position sensor typically triggers codes P0120 to P0124. P0120 and P0121 indicate the TPS signal is out of range, P0122 and P0123 indicate the signal is too low or too high, and P0124 indicates an intermittent signal. On drive-by-wire vehicles additional codes related to the electronic throttle control system may also be present.

Can a faulty TPS cause my automatic transmission to shift incorrectly?

Yes. The ECU shares throttle position data with the transmission control module to determine when to upshift and downshift. A faulty TPS sending incorrect throttle angle data can cause erratic shift points, harsh gear changes, the transmission hunting between gears, or the vehicle remaining in a fixed gear. Replacing the TPS often resolves transmission behaviour issues that appear unrelated.

Is it safe to drive with a faulty throttle position sensor?

It depends on how severely the sensor has failed. A partially failed TPS may cause hesitation and poor throttle response but the vehicle remains driveable. A fully failed TPS on a drive-by-wire vehicle can trigger limp mode, restricting the engine to a fixed low throttle position to prevent runaway acceleration. In either case replace the sensor as soon as possible as the fault can worsen without warning.

What are the symptoms of a faulty throttle position sensor?

Symptoms include jerky or hesitant acceleration, rough idle, unexpected surging, poor throttle response, stalling, and fault codes P0120-P0124. Drive-by-wire vehicles may also enter a limp mode limiting engine power.

Can I clean a throttle position sensor instead of replacing it?

TPS sensors are sealed units and cannot be cleaned or adjusted reliably. If the sensor is producing erratic signals or fault codes, replacement is the correct solution. Attempting to clean or adjust it usually results in continued faults.

Do I need to calibrate the throttle position sensor after replacement?

Many vehicles require a TPS calibration or throttle body relearn procedure after replacement. This is usually done with an OBD2 scanner or by following a specific ignition on/off sequence. Check your vehicle's service manual or contact us for guidance.

Identification
SKU	CTPS192-4
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CTPS192
Reference OEM Number	89452-35020
Other OEM Numbers	89452-35020, 89452-35100, 8945235020, 8945235100
Related Part Numbers	CTPS192, TPS-041, TH207, TP074, TTH028, TPS9099
Trade Part Numbers	VEMO: V70-72-0255, WALKER: 200-1238
Product Specifics
Sensor Type	Throttle position sensor
Number of pins	3-pin connector
Connector Shape	rectangular
Supplementary Article Info	without cable
Number of mounting bores	2
Rotation Direction	Anticlockwise rotation
Other Details
Note	Always verify fitment using your vehicle's OEM part number.
Unit Of Measure	ea