Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18 Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18

Camshaft Position Sensor for Suzuki JIMNY FJ SN413 1.3L M13A 00-18

Part #: 3322063J10 OEM #: 3322063J10 SKU: CSCA388-2

Aftermarket OEM Replacement for Suzuki JIMNY FJ SN413

$79.97
RRP $124.99
SAVE $45.02 (36%)
In Stock

BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT SUZUKI

 

Package Includes:

1* CAMSHAFT POSITION SENSOR (3-PIN PLUG).

 

OEM# 33220-63J10

  • [01/00 - 12/18] SUZUKI JIMNY FJ SN413 1.3L 4cyl M13A 62kW
  • [01/05 - 12/08] SUZUKI GRAND VITARA JT JB416 1.6L 4cyl M16A 73kW
  •  
  • [01/02 - 12/04] SUZUKI LIANA ER RH416 1.6L 4cyl M16A 76kW
  • [01/01 - 12/04] SUZUKI LIANA ER RH416 1.6L 4cyl M16A 76kW
  • [01/04 - 12/07] SUZUKI LIANA ER RH418 1.8L 4cyl M18A 92kW
  •  
  • [01/06 - 12/10] SUZUKI SWIFT EZ RS416 1.6L 4cyl M16A 92kW
  • [01/12 - 12/17] SUZUKI SWIFT FZ 1.6L 4cyl M16A 100kW
  • [01/05 - 12/10] SUZUKI SWIFT EZ RS415 1.5L 4cyl M15A 74kW
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA388-2
Barcode #8435050643181
BrandAftermarket OEM Replacement
Part Numbers
Part Number3322063J10
Reference OEM Number3322063J10
Other OEM Numbers33220-63J10, 33220-63J10-000
Related Part NumbersCHN3-A092, ADK87206, V64-72-0039
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Number of pins3 -pin connector
Connector Shapeoval
Supplementary Article Infowithout cable
Fitting Depth26.7 mm
Voltage12 V
Housing ColourBlack
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category