Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17 Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17

Cam Shaft Position Sensor for Toyota Hilux 1GRFE 4.0 V6 Ggn 05-17

Part #: CSCA147 OEM #: 90919-05060 SKU: CSCA147

Cam Shaft Position Sensor Toyota Hilux 1GRFE

$103.97
RRP $146.06
SAVE $42.09 (29%)
In Stock

BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT TOYOTA and LEXUS

 

TO SUIT:

 

OEM#

9091905060, 9008005060, 90919-05060

 

PACKAGE INCLUDES:

1 X OEM Quality CAMSHAFT POSITION SENSOR (3-PIN PLUG).

 

The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. Combining both sensor signals, the engine control unit knows when the first cylinder is at the top dead point.

  • [2005-2017] HILUX 4.0 V6 1GR-FE (GGN120R GGN125R GGN15R GGN25R)
  • [2015-ON] HILUX 2.8 1GD-FTV (GUN123R GUN136R) / 2.4 2GD-FTV (GUN122R GUN135R)
  • [2004-2009] LANDCRUISER PRADO 4.0L V6 1GR-FE (GRJ120R)
  •  
  • [2006-2017] AURION 3.5L V6 2GR-FE (GSV40R GSV50R)
  • [2007-2019] KLUGER 3.5L V6 2GR-FE /FKS (GSU40R GSU45R HSU50R GSU55R)
  • [09/17 - 12/21] CAMRY GSV70R 3.5L V6 2GR-FKS
  • [08/07 - 11/12] RAV4 GSA33R 3.5L V6 2GR-FE
  • [03/06 ON] TARAGO GSR50R 3.5L V6 2GR-FE
  • [05/08 - 12/14] VELLFIRE GGH20 (Gray Import) 3.5L V6 2GR-FE
  •  
  • [09/07 - 09/13] MARK X ZIO GGA10 (Gray Import) 3.5L V6 2GR-FE
  • [11/04 - 09/09] MARK X GRX121 (Gray Import) 3.0L V6 3GR-FSE NOTE: Suits Left Bank ONLY
  • [11/04 - 09/09] MARK X GRX120 GRX125 (Gray Import) 2.5L V6 4GR-FSE NOTE: Suits Left Bank ONLY
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA147
Barcode #9314258113599
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCSCA147
Reference OEM Number90919-05060
Other OEM Numbers9091905060, 9008005060, 90919-05060, 949979-1290
Related Part NumbersSC255, CHN3-V267, 0986280749, SS10939, 949979-1290
Trade Part NumbersDENSO: DCPS-0109, NTY: ECP-TY-014, VEMO: V63-72-0006
Product Specifics
Sensor TypeCAMSHAFT POSITION SENSOR
TypeSensor
Manufacturer Warranty1 Year
Number of pins3 -pin connector
Connector Shapeoval
Supplementary Article Infowith seal ring, without cable
Fitting Depth30 mm
Housing ColourBlack
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category