BRAND NEW *OEM Quality* mass airflow sensor to suit Hyundai iLoad / iMax / Santa Fe / Grandeur / Sonata and Kia Sorento / Carnival / Sportage / K2900 diesel engines. Also suits SsangYong Actyon and Rexton.

Limp mode, black smoke, rough idle or a P0100 code? A failing MAF sensor is one of the most common causes on these Hyundai / Kia and SsangYong diesel platforms. Workshop-grade replacement - dispatched from Cranbourne VIC.

TO SUIT

Hyundai iLoad TQ 2.5L D4CB CRDi (2008-2021)
Hyundai iMax TQ 2.5L D4CB CRDi (2008-2021)
Hyundai Santa Fe CM 2.2L D4EB CRDi (2006-2009)
Hyundai Grandeur TG 2.2L D4EB CRDi (2006-2010)
Hyundai Sonata NF 2.0L D4EA CRDi (2009-2010)
Kia Sorento JC 2.5L D4CB CRDi (2007-2009)
Kia Sportage KM 2.0L D4EA CRDi (2006-2010)
Kia Carnival VQ 2.9L J3 CRDi (2006-2011)
Kia K2700 2.7L J2 Diesel (2002-2008)
Kia K2900 2.9L J3 CRDi (2008-2012)
SsangYong Actyon C100 2.0L D20DT (2007-2011)
SsangYong Rexton RX320 3.2L M162 (2003-2006)

OEM PART NUMBERS

28164-27800 (Hyundai / Kia)
2816427800
28164-4A900
6650943148 (SsangYong)
A6650943148 (SsangYong)

OTHER PART NUMBERS

BOSCH: 0281002721
NTY: EPP-HY-503
VEMO: V52-72-0022

PACKAGE INCLUDES

1 x Mass Airflow Sensor - 5-pin rectangular connector, with integrated air temperature sensor, 80mm housing diameter, bolted mounting. We recommend replacing the air filter at the same time.

ABOUT THIS SENSOR

The mass airflow sensor measures the volume of air entering the engine and sends this data to the ECU, which uses it to calculate correct fuel delivery for D4CB, D4EB, D4EA and D20DT diesel engines.

When the sensor fails the ECU cannot maintain correct fuelling - causing limp mode, over-fuelling, black smoke and stored fault codes.

COMMON SYMPTOMS OF FAILURE

Vehicle entering limp mode under load
Rough or unstable idle
Hesitation or flat spot under acceleration
Black exhaust smoke under load
Poor fuel economy
Check engine light - fault codes P0100 P0101 P0102 P0103

[02/08 - 10/21] HYUNDAI iLOAD TQ CRDi (2.5L 4cyl D4CB 125kW)
[02/12 - 10/21] HYUNDAI iLOAD TQ CRDi (2.5L 4cyl D4CB 100kW)
[05/08 - 10/21] HYUNDAI iMAX TQ CRDi (2.5L 4cyl D4CB 125kW)
[02/12 - 10/21] HYUNDAI iMAX TQ CRDi (2.5L 4cyl D4CB 100kW)
[11/06 - 10/09] HYUNDAI SANTA FE CM II CRDi (2.2L 4cyl D4EB 114kW)
[06/06 - 10/10] HYUNDAI GRANDEUR TG CRDi (2.2L 4cyl D4EB 114kW)
[03/09 - 12/10] HYUNDAI SONATA NF V CRDi (2.0L 4cyl D4EA 110kW)
[08/07 - 09/09] KIA SORENTO JC I CRDi (2.5L 4cyl D4CB 125kW)
[01/06 - 08/10] KIA SPORTAGE JE / KM II CRDi (2.0L 4cyl D4EA 103kW)
[09/06 - 03/11] KIA CARNIVAL / GRAND CARNIVAL VQ III CRDi (2.9L 4cyl J3 141kW)
[10/02 - 12/08] KIA K2700 SD (2.7L 4cyl J2 59kW)
[01/08 - 12/12] KIA K2900 PU3 CRDi (2.9L 4cyl J3 92kW)
[01/07 - 12/11] SSANGYONG ACTYON C100 (2.0L 4cyl D20DT 104kW)
[01/03 - 12/06] SSANGYONG REXTON RX320 (3.2L 6cyl M162 162kW)

Can I clean my MAF sensor instead of replacing it?

Yes - if the sensor is contaminated rather than electrically failed, cleaning with a dedicated MAF sensor cleaner spray can restore correct readings. Do not use brake cleaner or generic electrical contact cleaner as these leave residue that damages the sensing wire. Allow the sensor to dry completely before reinstalling. If cleaning does not resolve the fault codes, the sensor requires replacement.

What is the difference between a MAF sensor and a MAP sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine using a hot wire element in the intake. A MAP (Manifold Absolute Pressure) sensor measures intake manifold pressure to calculate air density. Most modern engines use one or the other - some use both. Your vehicle service manual or OBD2 fault codes will confirm which sensor type your engine uses.

Will a faulty MAF sensor cause my vehicle to fail an emissions test?

Yes. A faulty MAF sensor causes the ECU to miscalculate fuel delivery, typically resulting in a rich running condition that increases CO and hydrocarbon emissions. Most roadworthy and emissions checks will fail a vehicle with an active MAF sensor fault code or visibly excessive exhaust smoke.

What are the symptoms of a bad MAF sensor?

Common symptoms include rough idle, hesitation or stumbling on acceleration, poor fuel economy, black smoke from the exhaust, and an illuminated Check Engine light. Your ECU may log fault codes P0100 to P0104.

Can I drive with a faulty MAF sensor?

You can drive short distances but it is not recommended. A faulty MAF sensor causes the ECU to run incorrect fuel mixtures, which can damage the catalytic converter and O2 sensors over time. Have it replaced as soon as possible.

How do I test if my MAF sensor is bad?

Use an OBD2 scanner to check for fault codes P0100-P0104. You can also use a multimeter or live data scanner to check the sensor output voltage against your vehicle's specification. A reading significantly outside spec confirms a faulty sensor.

What causes a MAF sensor to fail?

The most common causes are a dirty or contaminated sensing element (often from a missing or damaged air filter), oil contamination from an over-oiled aftermarket air filter, heat damage, or general wear over time.

Do I need to reset my ECU after replacing the MAF sensor?

It is good practice to clear any stored fault codes using an OBD2 scanner after replacement. Some vehicles will self-adapt within a short drive cycle, but clearing codes ensures the ECU recalibrates from a clean baseline.

Identification
SKU	CAF067-2816427800
Brand	OEM
Part Numbers
Part Number	2816427800
Reference OEM Number	28164-27800
Other OEM Numbers	2816427800, 28164-27800, 28164-4A900
Related Part Numbers	CAF067, AM2721N, DAMM901, 0281002721
Trade Part Numbers	BOSCH: 0281002721, VEMO: V52-72-0022
Product Specifics
Product Type	SENSOR
Sensor Type	Mass Airflow Sensor
Number of pins	5 -pin connector
Connector Shape	rectangular
Supplementary Article Info	with integrated air temperature sensor
Rated Voltage	12 V
Operating Mode	Electric
Recommended additional repairs	change Air Filter
Housing Diameter	80 mm
Emission Standard	Euro 4 (D4)
Other Details
Note	Always verify fitment using your vehicle's OEM part number.