Crankshaft Position Sensor for Holden Captiva CG LF1 LFW 3.0L V6 190kW 2011-2019
Direct Fit Replaces 12615626
BRAND NEW *OEM Quality* crankshaft position sensor to suit Holden Captiva CG 3.0L HFV6 V6 SIDI AWD with the LF1 and LFW engines.
If your Captiva is stalling without warning, failing to start, or logging a P0335 / P0336 fault - the crankshaft position sensor is a known wear item on the 3.0L HFV6 SIDI engine. Direct plug-in replacement. Dispatched same-day from Cranbourne VIC.
TO SUIT
This sensor suits the Holden Captiva CG with the 3.0L HFV6 LF1 SIDI engine (2011-2015) and the LFW SIDI engine (2015-2018/2019) in AWD 190kW configuration - refer to the full compatibility list below.
OEM PART NUMBERS
- 12615626
- 012615626
- J5T33671
- 01238249
- 1238249
OTHER PART NUMBERS
- V51-72-0194
- 235-1375
PACKAGE INCLUDES
1 x BRAND NEW crankshaft position sensor with 3-pin connector. Fitting depth: 38mm.
ABOUT THIS SENSOR
The crankshaft position sensor monitors crankshaft rotational speed and position and sends a continuous signal to the ECU for injection timing, ignition timing, and cylinder identification calculations.
On the Holden Captiva 3.0L HFV6 a failing crankshaft sensor typically causes intermittent stalling or a no-start condition. The car often restarts after cooling, which is a hallmark of a failing Hall-effect crankshaft sensor.
COMMON SYMPTOMS OF FAILURE
- Check engine light with fault code P0335 / P0336 / P0337 / P0338
- Engine stalls without warning at idle or under load
- Intermittent no-start - often restarts after cooling
- Engine misfires or vibrates under acceleration
- Rough or hunting idle
- Poor fuel consumption
- Holden Captiva CG 3.0L HFV6 LF1 SIDI AWD 190kW [03/11 - 09/15]
- Holden Captiva CG 3.0L HFV6 LFW SIDI AWD 190kW [10/15 - 12/18]
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCSCA458-Captiva |
| Reference OEM Number | 12615626 |
| Other OEM Numbers | 12615626, J5T33671, 01238249, 1238249, 012615626 |
| Related Part Numbers | CAS-288, SC517, TCAS400, EH065, PC920, CSCA458 |
| Interchange Part Numbers | V51-72-0194, 235-1375 |
| Product Specifics | |
| Sensor Type | CRANKSHAFT POSITION SENSOR |
| Type | Sensor |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Fitting Depth | 38 mm |
| Compatible Makes | Holden |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.