Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300 Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300

Crankshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L G4KG 39180-25300

Part #: 3918025300 OEM #: 39180-25300 SKU: 3918025300-SC090GEN_1

Workshop Grade Replaces 39180-25300

$97.97
RRP $127.36
SAVE $29.39 (23%)
In Stock

BRAND NEW *OEM Quality* crank angle sensor for Hyundai iLoad and iMax TQ 2.4L G4KG vans and buses.

A failing crank angle sensor on the iLoad/iMax TQ causes hard starting and stalling that can leave a work van off the road - this rear-mounted sensor restores accurate signal to the ECU. Same-day dispatch before 12pm from Cranbourne VIC.

TO SUIT

Suits the Hyundai iLoad TQ Cargo and iMax TQ Travel 2.4L G4KC/G4KG petrol RWD van and bus range built from 2008 to 2016. Rear-mounted 3-pin sensor, direct OEM replacement.

OEM PART NUMBERS

  • 39180-25300
  • 3918025300
  • 39180-25200

OTHER PART NUMBERS

  • VEMO: V52-72-0154
  • NTK-AU: EH0400
  • HELLA: 6PU 009 168-991

PACKAGE INCLUDES

1x OEM crank angle sensor (3-pin connector, rear-mount, with seal ring and cable).

ABOUT THIS SENSOR

The crank angle sensor on the iLoad/iMax TQ's 2.4L G4KC/G4KG engine tracks crankshaft position so the ECU can time fuel injection and ignition correctly. These commercial vans rack up high daily kilometres, and heat cycling around the engine bay is a common cause of early sensor failure on this platform.

A degraded sensor often shows up as a stall at idle when the van is fully loaded or stopped in traffic, sometimes clearing itself once the engine cools - a classic sign the sensor needs replacing before it fails completely.

COMMON SYMPTOMS OF FAILURE

  • Van stalls at idle or in traffic, especially when hot
  • Difficulty restarting after a hot stall
  • Check engine light with fault code P0335 or P0336
  • Rough idle when loaded
  • Hesitation under acceleration
  • Reduced fuel economy
  • [2008 - 2016] HYUNDAI ILOAD TQ CARGO 2.4L 4cyl G4KC/G4KG RWD (129kW)
  • [2008 - 2016] HYUNDAI IMAX TQ TRAVEL 2.4L 4cyl G4KC/G4KG RWD (129kW)
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKU3918025300-SC090GEN_1
BrandAftermarket OEM Replacement
Part Numbers
Part Number3918025300
Reference OEM Number39180-25300
Other OEM Numbers39180-25300, 3918025300, 39180-25200
Related Part NumbersCSCA360G, EH0400, PC710, SC090, SS11329
Trade Part NumbersVEMO: V52-72-0154, NTK-AU: EH0400, HELLA: 6PU 009 168-991
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT / CRANKSHAFT POSITION SENSOR
Fitting PositionRear
Number of pins3-Pin
Connector Shaperectangular
Supplementary Article InfoWith seal ring, with cable
Fitting Depth39 mm
Rated Voltage12V
Housing ColourBlack
Cable Length285 mm
Fitment TypeDirect Replacement
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category