Crankshaft Position Sensor for BMW Z3 Z4 E36 E85 Roadster M52 M54 N52 Six
OEM Spec Fit Replaces 12141709616
BRAND NEW *OEM Quality* crankshaft position sensor to suit BMW Z3 and Z4 roadsters.
If your Z3 or Z4 cuts out on a warm day, will not restart until it cools or shows a crank sensor fault, this is the fix. Dispatched from Victoria same-day before 12pm.
TO SUIT
Fits the BMW Z3 E36 2.0i 2.2i 2.8i and 3.0i from 1998 to 2003 with the M52 and M54 six, and the Z4 E85 2.5i and 3.0i M54 from 2003 plus the 2.5si and 3.0si N52 to 2008.
OEM PART NUMBERS
- 12141709616
- 12141744492
- 1709616
- NSC106100
OTHER PART NUMBERS
- V20-72-0403
- 6PU012680-011
- 254062
- 235-1252
- S107230001Z
PACKAGE INCLUDES
1 x BRAND NEW crankshaft position sensor with 3-pin D-shaped connector.
ABOUT THIS SENSOR
The crank sensor sits at the rear of the six-cylinder block and reads the flywheel-end reluctor so the DME can time spark and fuel. Heat soak around the rear of the block is a common cause of failure on these roadsters.
When it starts to fail the engine may cut out at idle or under load and refuse to restart hot. A dead sensor gives no RPM signal at all and the car will crank without firing.
COMMON SYMPTOMS OF FAILURE
- Cuts out when warm and will not restart hot
- Cranks with no start
- Engine light with codes P0335 P0336 or P0339
- Erratic idle and hesitation
- [07/98 - 05/00] BMW Z3 E36 i (2.8L 6cyl M52 B28 (286S1)/ M52 B28 (286S2) 142kW)
- [06/99 - 10/00] BMW Z3 E36 i (2.0L 6cyl M52 B20 (206S4) 110kW)
- [06/00 - 01/03] BMW Z3 E36 i (3.0L 6cyl M54 B30 (306S3) 170kW)
- [10/00 - 06/02] BMW Z3 E36 i (2.2L 6cyl M54 B22 (226S1) 125kW)
- [07/03 - 12/06] BMW Z4 E85 i (2.5L 6cyl M54 B25 (256S5) 141kW)
- [07/03 - 12/05] BMW Z4 E85 i (3.0L 6cyl M54 B30 (306S3) 170kW)
- [01/06 - 08/08] BMW Z4 E85 si (2.5L 6cyl N52 B25 A 160kW)
- [01/06 - 08/08] BMW Z4 E85 si (3.0L 6cyl N52 B30 BF/ N52 B30 A 195kW)
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCSCA140 |
| Reference OEM Number | 12141709616 |
| Other OEM Numbers | 12141709616, 12141744492, 1709616, NSC106100 |
| Related Part Numbers | SC276, V20-72-0403, TCAS229, CSCA140 |
| Interchange Part Numbers | V20-72-0403, 6PU012680-011, 254062, 235-1252, S107230001Z |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CRANKSHAFT POSITION SENSOR |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Fitting Depth | 33mm |
| Rated Voltage | 12V |
| Housing Colour | Black |
| Number of mounting bores | 1 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.