BRAND NEW *OEM QUALITY* CRANKSHAFT POSITION SENSOR TO SUIT TOYOTA DYNA & COASTER BUS

PLEASE COMPARE YOUR ORIGINAL SENSOR WITH THE IMAGES WE PROVIDED IN THE LISTING AND CHECK THE DETAILED VEHICLE LIST IN THE SUITABILITY SECTION.

TO SUIT:

[1994-2006] Toyota Dyna (200 250 300 400) & Coaster BB50 15B-FTE 4.1L Engine

OEM# 90919-05063

• for OE No: 90919-05063
• Number of pins: 2 -pin connector
• Sensor Type: Inductive Sensor
• Resistor: 2.1 kOhm
• Supplementary Article/Info 2: without cable

Features:

• High Quality
• OEM Fit and Design
• Easy install
• Simple operation
• AU Seller-Fast and Free Shipping

Package Includes:

1* CRANKSHAFT POSITION SENSOR (2 PIN PLUG)

The crankshaft position sensor is an engine management component found on virtually all modern vehicles with internal combustion engines. It monitors the position and rotational speed of the crankshaft and sends the information to the engine control unit so it can make appropriate adjustments based on operating conditions. The crankshaft speed and position are some of the most important parameters used in engine management calculations, and many engines cannot run if the crankshaft position sensor is not providing an accurate signal.

Faulty crankshaft position sensor symptoms:

• Issues Starting the Vehicle
• Intermittent Stalling
• Check Engine Light Comes On
• Uneven Acceleration
• Engine Misfires or Vibrates
• Rough Idle and/or Vibrating Engine
• Reduced Gas Mileage

COMPATIBLE VEHICLES

Toyota Dyna 250 Van 4.1 TDi (BU223) RWD Diesel 4.1L 4cyl 125kW 15B-FTE 4104cc 125kW (Diesel)
Toyota Dyna 300 Platform/Chassis 4.1 D RWD Diesel 4.1L 4cyl 92kW 15B-FTE 4104cc 92kW (Diesel)
Toyota Dyna 400 XZU3,BU4 Platform/Chassis 4.1 TDi RWD Diesel 4.1L 4cyl 125kW 15B-FTE 4104cc 125kW (Diesel)
Toyota Dyna 300 XZU300,XZU320,XZU330,XZU340 Platform/Chassis 4.1 Tdi RWD Diesel 4.1L 4cyl 125kW 15B-FTE 4104cc 125kW (Diesel)
Toyota Dyna 200 Platform/Chassis 4.1 TDi (BU223) RWD Diesel 4.1L 4cyl 110kW 15B-FTE 4104cc 110kW (Diesel)
Toyota Dyna 200 Platform/Chassis 4.1 TDi (BU223) RWD Diesel 4.1L 4cyl 125kW 15B-FTE 4104cc 125kW (Diesel)
Toyota Coaster BB50 Bus 4.1 TD RWD Diesel 4.1L 4cyl 100kW 15B-FTE 4104cc 100kW (Diesel)
Toyota Coaster BB50 Bus 4.1 TD RWD Diesel 4.1L 4cyl 114kW 15B-FTE 4104cc 114kW (Diesel)

ABOUT YOUR VEHICLE’S CAMSHAFT / CRANKSHAFT POSITION SENSOR

What does a Camshaft/Crankshaft Position Sensor do?
The Camshaft sensor determines which cylinder is firing to establish injector synchronization and coil firing sequence in DIS systems. Crankshaft sensors set ignition timing, supply the RPM signal, and determine engine speed.

Where are these sensors located?
The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.

Will a malfunctioning Cam or Crank Sensor illuminate the check engine light or affect vehicle operation?
Yes, a failing sensor can illuminate the MIL and may cause vehicle stalling or a no-start condition.

What are the common causes of failure?
Typically these sensors fail due to exposure to high heat.

How to determine if these sensors are malfunctioning?
Look for RPM on a scan tool while cranking the engine. If the engine runs, a scope is the best diagnostic tool. Typical trouble codes: Crankshaft P0335; Camshaft P0340.

What makes Our Standard Camshaft and Crankshaft Position Sensors the best?
Integrated A/D converter and digital signal processing with a dynamically adaptive switch point improves accuracy and operation
Advanced circuitry protects the system from stray electro-magnetic fields and power spikes
Custom magnetic circuit programming calibrates the sensor while performance testing for improved timing accuracy between the target wheel and sensor output
100% environmental, endurance, and end-of-line testing for Timing, Pulse Width, and Signal Amplitude ensures consistent product reliability