Camshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073AC Camshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073ACCamshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073AC

Camshaft Position Sensor for Ford Everest UA UA II TDCi 3.2L P5AT 6C1112K073AC

Part #: 6C1112K073AC OEM #: 6C11-12K073-AC SKU: CSCA432-Everest

Heavy Duty Fit Replaces 6C1112K073AC

$78.45
RRP $147.07
SAVE $68.62 (47%)
In Stock

BRAND NEW *OEM Quality* camshaft position sensor to suit Ford Everest UA and UA II 3.2L TDCi P5AT diesel.

The Everest UA uses the same P5AT 3.2L five-cylinder Duratorq as the Ranger PX - a cam sensor fault typically shows as P0340 or P0345 and can cause a no-start or rough idle on the P5AT engine. This is a direct replacement verified for the Everest UA platform. Dispatched from Melbourne same-day before 12pm with express delivery available.

TO SUIT

Ford Everest UA and UA II 3.2L TDCi P5AT diesel (July 2015 to May 2022), both AWD and RWD variants. Also suits Ford Ranger PX/PXII/PXIII 3.2L P5AT TDdi diesel with the same engine. Full vehicle list below.

OEM PART NUMBERS

  • 1132919
  • 1219993
  • 1347419
  • 1358343
  • 1811604
  • 1780382
  • 2S7Q12K073AA
  • 2S7Q12K073BA
  • 2S7Q12K073BB
  • 6C1112K073AA
  • 6C1112K073AB
  • 6C1112K073AC
  • 6C11-12K073-AA
  • 6C11-12K073-AB
  • 6C11-12K073-AC

OTHER PART NUMBERS

  • BOSCH: 0986280732
  • VEMO: V25-72-1049
  • WALKER: 235-1927
  • NTY: ECP-FR-001

PACKAGE INCLUDES

1 x OEM Quality Camshaft Position Sensor - 3-pin oval connector, grey housing.

ABOUT THIS SENSOR

The Ford Everest UA runs the same P5AT 3.2L five-cylinder Duratorq engine as the Ranger PX. The camshaft position sensor on the P5AT feeds real-time cam position data to the PCM for injection timing - unlike petrol engines where ignition timing is primary, on the TDCi the CMP signal directly influences pilot and main injection events. A degrading sensor causes progressive rough running before eventual no-start.

This replacement is cross-referenced against TecDoc for the Everest UA/UA II platform and provides a plug-and-play fit with the factory 3-pin oval connector. Specialist sensor retailer stocked in Melbourne.

COMMON SYMPTOMS OF FAILURE

  • P0340 or P0345 fault codes (camshaft position sensor circuit)
  • No-start on cold mornings - P5AT cranks without firing
  • Rough idle or engine shake at idle speed
  • Intermittent stall under light throttle
  • Excessive black smoke on acceleration
  • Limp mode or reduced power on the Everest UA
  • [07/15 - 05/22] FORD EVEREST UA,UA II TDCi 3.2L 5cyl P5AT 143kW AWD
  • [07/15 - 05/22] FORD EVEREST UA,UA II TDCi 3.2L 5cyl P5AT 143kW RWD
  •  
  • [11/11 - 05/22] FORD RANGER PX,PXII,PXIII TDdi 3.2L 5cyl P5AT 147kW
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA432-Everest
BrandAftermarket OEM Replacement
Part Numbers
Part Number6C1112K073AC
Reference OEM Number6C11-12K073-AC
Other OEM Numbers6C1112K073AC, 6C1112K073AA, 6C1112K073AB, 1780382, 2S7Q12K073AA
Related Part NumbersCAM-121, CSCA432, SC433
Trade Part NumbersBOSCH: 0986280732, VEMO: V25-72-1049, WALKER: 235-1927
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Manufacturer Warranty1 Year
Fitting PositionCam Sensor
Number of pins3-Pin
Connector Shapeoval
Housing ColourGrey
Number of mounting bores1
Compatible MakesFord
Fitment TypeDirect Replacement
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

Others Also Bought

More From This Category