





Camshaft Position Sensor for Kia Cerato LD YD (G4NB G4GB G4GC) 1.8L 2.0L
Direct Fit Replaces 39350-23910
BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT KIA CERATO LD YD KOUP (G4NB G4GB G4GC) 1.8L 2.0L
IMPORTANT FITMENT CHECK
Engineered for the 1.8L and 2.0L Petrol engines utilized across the Kia fleet. When your original sensor degrades from extreme engine heat it fails to read the camshaft lobes correctly triggering a Check Engine Light and restricting engine power.
Ships Daily from our Cranbourne VIC Warehouse. Unsure about fitment? Contact Our expert team.
COMPATIBLE VEHICLES
- Kia Cerato & Koup (2004-2021) 1.8L 2.0L Petrol
- Kia Sportage KM QL (2007-2023) 2.0L Petrol
- Kia Soul AM (2009-2021) 2.0L Petrol
- Kia Rondo (2015-2021) 2.0L Petrol
REPLACES PART NUMBERS
- Kia: 39350-23910 3935023910
- Trade Reference: CSCA395 SU12980 5S11527
PACKAGE INCLUDES:
1 X OEM CAMSHAFT POSITION SENSOR (3-PIN PLUG).
The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. The engine control unit knows when the first cylinder is at the top dead point through the combination of both sensor signals.
COMMON QUESTIONS
Do I need to clear the engine codes after installation?
While the vehicle will often run normally immediately after installation it is highly recommended to use an OBD2 scan tool to clear the stored fault codes from the ECU.
- [06/04 - 07/09] KIA CERATO LD I 2.0L 4cyl G4GC Euro 4 105kW
- [04/13 - 03/16] KIA CERATO YD III 1.8L 4cyl G4NB 110kW
- [06/13 - 02/16] KIA CERATO YD,YDM III 1.8L 4cyl G4NB 110kW
- [09/14 - 03/16] KIA CERATO KOUP YD III GDi 2.0L 4cyl G4NC 129kW
- [06/13 - 02/16] KIA CERATO YD III GDI 2.0L 4cyl G4NC 129kW
- [06/13 - 02/16] KIA CERATO YD,YDM III GDI 2.0L 4cyl G4NC 129kW
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | 3935023910-Cerato |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CSCA395 |
| Reference OEM Number | 39350-23910 |
| Other OEM Numbers | 3935023910, 3935023700, 39350-23700, 39350-23910 |
| Related Part Numbers | EC0289, SS11353, CSCA116, CSCA395, SC239 |
| Trade Part Numbers | VEMO: V53-72-0116, WALKER: 235-1273 |
| Product Specifics | |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Type | Sensor |
| Features | Direct Fit |
| Manufacturer Warranty | 1 Year |
| Number of pins | 3 -pin connector |
| Connector Shape | rectangular |
| Supplementary Article Info | without cable, with seal ring |
| Fitting Depth | 28.2 mm |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.