Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008 Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008

Camshaft Position Sensor for Renault Megane X84 1.6L K4M 2003-2008

Part #: CAM-133 OEM #: 8200033686 SKU: CSCA545-5

OEM Spec Fit Replaces 8200033686

$149.10
RRP $182.11
SAVE $33.01 (18%)
In Stock

BRAND NEW *OEM Quality* camshaft position sensor to suit Renault Megane X84 1.6L K4M petrol.

If your Megane is hesitating, idling roughly or has a check engine light on - this direct-fit sensor restores accurate camshaft timing. Dispatched same-day from Cranbourne VIC.

TO SUIT

This camshaft position sensor suits the Renault Megane II X84 hatchback (2002-2008) fitted with the 1.6L 16V K4M petrol engine.

OEM PART NUMBERS

  • 8200033686
  • 8200285798
  • 7485129995

OTHER PART NUMBERS

  • HELLA: 6PU 009 146-611
  • WALKER PRODUCTS: 235-1926
  • NTK: CHN3-A221
  • DT SPARE PARTS: 6.27360

PACKAGE INCLUDES

1 x OEM Quality camshaft position sensor with 3-pin oval connector.

ABOUT THIS SENSOR

A camshaft position sensor tells the engine control unit exactly where the camshaft is in its rotation. Working together with the crankshaft sensor, this signal lets the ECU time fuel injection and ignition accurately for each cylinder.

As the sensor wears or its signal weakens, timing becomes less precise. This can cause hard starting, rough idle, stalling, or a sudden loss of power along with a check engine light.

COMMON SYMPTOMS OF FAILURE

  • Engine cranks but takes longer than normal to start
  • Intermittent stalling, especially when hot
  • Rough idle or hesitation under acceleration
  • Sudden loss of power
  • Check engine light on (fault codes P0340-P0344)
  • Engine fails to start at all
  • [11/02 - 02/08] RENAULT MEGANE II X84 Hatchback 1.6L 16V K4M 83kW FWD
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUCSCA545-5
Barcode #4047025204378
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCAM-133
Reference OEM Number8200033686
Other OEM Numbers8200033686, 8200285798, 7485129995
Related Part Numbers0986280433, CSCA545, SC434
Trade Part NumbersHELLA: 6PU 009 146-611, NTK: CHN3-A221
Product Specifics
TypeCamshaft Position Sensor
Number of pins3-Pin
Connector Shapeoval
Rated Voltage12V
Housing ColourBlack
Operating ModeElectric
Compatible MakesRenault
Fitment TypeDirect Replacement
BrandAftermarket OEM Replacement
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

Others Also Bought

More From This Category