
Oxygen Sensor Pre-Cat for Toyota Lexus (2GRFE 2AZFE Engines) 300MM LONG
Direct Fit Replaces 894670E020
Pre-cat oxygen sensor for Toyota Camry ACV36, RAV4, Kluger GSU40, Aurion GSV40, Tarago ACR30/ACR50, and Lexus RX350 and RX450h with 2GR-FE and 2AZ-FE engines. OEM 894670E020. Same-day dispatch from Cranbourne VIC.
TO SUIT
Toyota Camry ACV36 2.4L 2AZ-FE, Kluger GSU40/45 3.5L 2GR-FE, Aurion GSV40 3.5L 2GR-FE, RAV4 ACA38 2.4L 2AZ-FE, Tarago ACR30/ACR50 2.4L 2AZ-FE, and Lexus RX350 GSU35 3.5L 2GR-FE and RX450h GYL10/GYL15 3.5L 2GR-FXE. See compatibility table for full vehicle list.
FITMENT CHECK
Pre-cat (upstream) position. Thread: M18x1.5. Connector: 4-pin. Cable: 300mm. Confirm OEM 894670E020 before ordering. Two sensors required on V6 2GR-FE models.
OEM PART NUMBERS
- 894670E020 (Toyota primary)
- 8946748020 (Toyota)
- 8946760020 (Toyota)
OTHER PART NUMBERS
- F00E262805 (Bosch cross-ref)
PACKAGE INCLUDES
1 x pre-cat oxygen sensor - 4-pin connector - 4-wire - 300mm cable - M18x1.5 thread.
ABOUT THIS SENSOR
The pre-cat oxygen sensor on Toyota 2GR-FE and 2AZ-FE engines provides exhaust lambda feedback to the ECU for closed-loop fuel trim control. The 2GR-FE V6 requires two sensors (one per bank). Failure sets codes P0130 P0135 P0150 P0155 and causes open-loop running and increased fuel consumption.
COMMON SYMPTOMS OF FAILURE
- Check engine light with codes P0130 P0135 P0150 P0155
- Increased fuel consumption
- Rough idle or poor throttle response
- Failed emissions test
- TOYOTA
- [01/02 - 12/06] TOYOTA CAMRY ACV36 2.4L 4cyl 2AZ-FE 116kW (Pre-Cat)
- [01/07 - 12/09] TOYOTA AURION GSV40 3.5L V6 2GR-FE 203kW (Pre-Cat)
- [01/07 - 12/13] TOYOTA KLUGER GSU40 GSU45 3.5L V6 2GR-FE 200kW (Pre-Cat)
- [01/06 - 12/12] TOYOTA RAV4 ACA38 2.4L 4cyl 2AZ-FE 116kW (Pre-Cat)
- [01/00 - 12/05] TOYOTA TARAGO ACR30 2.4L 4cyl 2AZ-FE (Pre-Cat)
- [01/06 - 12/14] TOYOTA TARAGO ACR50 2.4L 4cyl 2AZ-FE (Pre-Cat)
- LEXUS
- [01/06 - 12/12] LEXUS RX GSU35 350 3.5L V6 2GR-FE 200kW (Pre-Cat)
- [01/09 - 12/15] LEXUS RX GYL10 GYL15 450h 3.5L V6 2GR-FXE 183kW (Pre-Cat)
How do I replace an oxygen sensor?
Most O2 sensors thread directly into the exhaust pipe or manifold. You will need an O2 sensor socket (22mm with a slot for the wire) and penetrating oil if the sensor is seized. Allow the exhaust to cool completely before starting. Some sensors also require a wiring harness connector to be unplugged. Always clear fault codes with an OBD2 scanner after replacement.
What fault codes does a faulty O2 sensor trigger?
A faulty O2 sensor typically triggers codes P0130 to P0167. The specific code indicates which sensor has failed - P0130 to P0138 relate to Bank 1 sensors and P0150 to P0158 relate to Bank 2 sensors. An OBD2 scanner will identify the exact sensor location.
Can I use a universal O2 sensor on my vehicle?
Universal sensors can work but require splicing the wiring harness which introduces risk of connection faults. A direct-fit aftermarket OEM replacement sensor with the correct connector plugs directly in with no cutting or splicing required. SensorGal stocks direct-fit sensors cross-referenced to OEM part numbers for most Australian vehicles.
How do I know if my O2 sensor is bad?
Common signs include poor fuel economy, rough idle, failed emissions test, rotten egg smell from the exhaust, and a Check Engine light with codes P0130-P0167. An OBD2 scanner showing a flat or sluggish O2 sensor waveform on live data also indicates a faulty sensor.
What is the difference between upstream and downstream O2 sensors?
The upstream (pre-cat) sensor monitors exhaust gases to help the ECU calculate fuel trim. The downstream (post-cat) sensor monitors catalytic converter efficiency. They serve different functions and are not interchangeable even if they look identical.
Can a bad O2 sensor damage my catalytic converter?
Yes. A faulty upstream O2 sensor can cause the engine to run rich, sending unburnt fuel into the catalytic converter. Over time this overheats and destroys the catalyst. Replacing the O2 sensor promptly protects your catalytic converter.
How many O2 sensors does my vehicle have?
Most 4-cylinder vehicles have two O2 sensors (one upstream, one downstream). V6 and V8 engines typically have four - one upstream and one downstream per bank. Contact us with your vehicle details and we will confirm the correct quantity and part numbers.
| Identification | |
|---|---|
| SKU | F00E262805 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | 8946707020 |
| Reference OEM Number | 894670E020 |
| Other OEM Numbers | 894670E020, 894670E010, 8946707020 |
| Product Specifics | |
| Type | Oxygen Sensor |
| Thread Size | M18x1.5 |
| Number of pins | 4 -pin connector |
| Cable Length | 300 mm |
| Fitment Type | Direct Replacement |
| Brand | Aftermarket Replacement |
| Sensor Sub-Type | Narrowband Switching-Type Oxygen Sensor |
| Placement | Pre-Catalytic Converter |
| Number of Wires | 4 |
| Other Details | |
| Note | 4-pin connector - 4-wire - 300mm cable - M18x1.5 |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.