



Cam Angle Sensor for Commodore/BERLINA VE VF 3.0 V6 SIDI (LF1/LFW)
Cam Angle Sensor VE VF Commodore V6 SIDI Direct Fit
BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT HOLDEN / GM
TO SUIT:
HOLDEN HFV6 LF1 / LW2 / LWR / LLT / LFX / LFW / SIDI 3.0 3.6 V6 Engines
- [2010-2018] COMMODORE / BERLINA VE VF 3.0 V6 SIDI (LF1 / LFW)
- [2006-2013] COMMODORE / CALAIS VE 3.6 V6 SIDI / SV6 (LF1 / LWR / LLT / LFX)
- [2013-2017] COMMODORE / CALAIS VF 3.6 V6 SIDI / SV6 ( LFX/ LWR)
- [2006-2015] STATESMAN / CAPRICE WM 3.6 V6 (LFX/ LWR / LY7)
- [2011-2018] CAPTIVA CG 3.0L HFV6 LF1/ LFW SIDI
OEM# 12615371, 1237191, 12684186
Package Includes:
1 X OEM Quality CAMSHAFT POSITION SENSOR (3-PIN PLUG).
The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. The engine control unit knows when the first cylinder is at the top dead point through the combination of both sensor signals.
- [05/08 - 05/13] HOLDEN CALAIS VE i V6 3.6L V6 LLT 210kW
- [09/09 - 05/13] HOLDEN CALAIS VE i V6 3.6L V6 LY7 195kW
- [06/13 - 10/17] HOLDEN CALAIS VF i V6 3.6L V6 LFX 210kW
- [09/10 - 04/13] HOLDEN CAPRICE SERIES 2 3.6L V6 HFV6 LWR 180kW
- [07/06 - 08/13] HOLDEN CAPRICE WM i V6 3.6L V6 H7,LY7 195kW
- [08/09 - 08/13] HOLDEN CAPRICE WM i V6 3.6L V6 LFX,LLT 210kW
- [07/06 - 08/13] HOLDEN CAPRICE WM i V6 3.6L V6 LWR 180kW
- [01/12 - 08/13] HOLDEN CAPRICE WM i V6 LPG 3.6L V6 LWR 180kW
- [05/13 - 08/15] HOLDEN CAPRICE WN i V6 3.6L V6 LFX 210kW
- [05/13 - 08/15] HOLDEN CAPRICE WN i V6 LPG 3.6L V6 LWR 180kW
- [07/12 - 12/15] HOLDEN CAPTIVA 7 CG Gen. II Flexfuel 3.0L V6 LFW 190kW
- [03/11 - 12/18] HOLDEN CAPTIVA 7 CG Gen. II i 3.0L V6 LF1 190kW
- [09/10 - 10/13] HOLDEN COMMODORE VE i V6 3.0L V6 LF1 190kW
- [09/09 - 05/13] HOLDEN COMMODORE VE i V6 3.0L V6 LFW,LF1 190kW
- [11/08 - 05/13] HOLDEN COMMODORE VE i V6 3.6L V6 LE0,LW2(218CUV6),HB 175kW
- [09/11 - 05/13] HOLDEN COMMODORE VE i V6 3.6L V6 LFX,LLT 210kW
- [09/11 - 10/13] HOLDEN COMMODORE VE i V6 3.6L V6 LFX,LLT 210kW
- [09/09 - 05/13] HOLDEN COMMODORE VE i V6 3.6L V6 LFX,LLT 210kW
- [09/09 - 10/13] HOLDEN COMMODORE VE i V6 3.6L V6 LFX,LLT 210kW
- [08/06 - 05/13] HOLDEN COMMODORE VE i V6 Dual Fuel LPG 3.6L V6 HB,LE0,LW2(218CUV6) 175kW
- [09/07 - 10/13] HOLDEN COMMODORE VE i V6 Dual Fuel LPG 3.6L V6 HN,LE0,LW2(218CUV6) 175kW
- [02/12 - 05/13] HOLDEN COMMODORE VE i V6 LPG 3.6L V6 LWR 180kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i SV6 3.6L V6 LFX 210kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i SV6 3.6L V6 LY7 180kW
- [05/13 - 08/15] HOLDEN COMMODORE VF i SV6 LPG 3.6L V6 LWR 180kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i SV6 LPG 3.6L V6 LWR 180kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i V6 3.0L V6 LF1 185kW
- [05/13 - 12/14] HOLDEN COMMODORE VF i V6 3.0L V6 LFW 190kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i V6 3.0L V6 LFW,LF1 185kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i V6 3.6L V6 LY7 180kW
- [05/13 - 10/17] HOLDEN COMMODORE VF i V6 Flexfuel 3.0L V6 LF1 185kW
- [05/13 - 08/15] HOLDEN COMMODORE VF i V6 LPG 3.6L V6 LWR 180kW
- [01/15 - 12/16] HOLDEN INSIGNIA GA VXR 2.8L V6 A 28 NER Euro 5 239kW
- [08/09 - 12/10] HOLDEN STATESMAN WM i V6 3.6L V6 LLT 210kW
- [07/06 - 12/10] HOLDEN STATESMAN WM i V6 3.6L V6 LY7 180kW
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA440-1 |
| Barcode # | 9341554040519 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CSCA440 |
| Reference OEM Number | 12684186 |
| Other OEM Numbers | 12615371, 1237191, 12684186 |
| Related Part Numbers | 12615371, C516, CAM-115, CSCS440, SU13631, TCAS376 |
| Product Specifics | |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Type | Sensor |
| Features | Direct Fit |
| Manufacturer Warranty | 1 Year |
| Make | HOLDEN |
| Number of pins | 3 -pin connector |
| Connector Shape | oval |
| Supplementary Article Info | without cable |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.