MAP Sensor for Saab 9-3 2.8L V6 Turbo LP9 B284L B284R MAP Sensor for Saab 9-3 2.8L V6 Turbo LP9 B284L B284R MAP Sensor for Saab 9-3 2.8L V6 Turbo LP9 B284L B284R MAP Sensor for Saab 9-3 2.8L V6 Turbo LP9 B284L B284R

MAP Sensor for Saab 9-3 2.8L V6 Turbo LP9 B284L B284R

Part #: SCMS265 Replaces OEM: 12575467

OEM Spec Fit Replaces 12575467

$92.99
RRP $148.99
SAVE $56.00 (38%)
In Stock

BRAND NEW *OEM Quality* MAP sensor to suit Saab 9-3 with the 2.8L V6 Turbo engine.

Rough idle, poor turbo response, or a check engine light on your 9-3? A failing MAP sensor is a common cause on the B284L and LP9 engines. This is a direct OEM-spec fit with a 3-pin oval connector. Stocked in Melbourne and dispatched same-day before 12pm.

TO SUIT

This sensor suits the Saab 9-3 Sedan (YS3F) and Wagon (E50) with the 2.8L V6 Turbo from 2005 to 2015, covering engine codes LP9 (184kW), B284L (188kW), and B284R (206kW XWD). Includes both FWD and AWD variants.

OEM PART NUMBERS

  • 12575467
  • 93194419
  • 24420587
  • 638562
  • 4709502
  • 6235707
  • 6235728
  • 71741115
  • 18590-73KA0
  • 18590-T73KA0

OTHER PART NUMBERS

  • 0261230101
  • MA0204
  • 225-1095
  • V40-72-0572

PACKAGE INCLUDES

1 x MAP Sensor - 3-pin oval connector, 10-115 kPa pressure range.

ABOUT THIS SENSOR

The MAP sensor measures intake manifold pressure and feeds this data to the ECU, which uses it to calculate correct fuelling and boost management for the turbocharged V6.

When the sensor fails, the ECU cannot accurately measure engine load, causing incorrect fuelling - particularly noticeable under boost.

COMMON SYMPTOMS OF FAILURE

  • Rough or unstable idle
  • Hesitation under acceleration or boost
  • Poor fuel economy
  • Reduced power or flat boost response
  • Check engine light - codes P0105 P0106 P0107 P0108
  • [03/05 - 02/15] SAAB 9-3 D75/ D79/ E79/ YS3F Turbo V6 2.8L V6 LP9 184kW
  • [12/07 - 02/15] SAAB 9-3 E50 Turbo V6 2.8L V6 B284L 188kW
  • [05/08 - 12/11] SAAB 9-3 E50 Turbo V6 2.8L V6 B284R 206kW
  • [03/05 - 02/15] SAAB 9-3 E50 Turbo V6 2.8L V6 LP9 184kW
  • [12/07 - 02/15] SAAB 9-3 YS3F Turbo V6 2.8L V6 B284L 188kW
What fault codes does a faulty MAP sensor trigger?

A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.

How do I test a MAP sensor?

With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.

Can I drive with a faulty MAP sensor?

You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.

What does a MAP sensor do?

The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.

What are the symptoms of a faulty MAP sensor?

Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.

What is the difference between a MAP sensor and a MAF sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.

Identification
BrandAftermarket OEM Replacement
Part Numbers
Part NumberSCMS265
Reference OEM Number12575467
Other OEM Numbers12575467, 24420587, 93194419, 71741115, 6235707, 6235728
Related Part NumbersMAP-051, MA0204, MP157, CMS265
Interchange Part Numbers0261230101, 225-1095, V40-72-0572
Product Specifics
Product TypeSENSOR
Sensor TypeManifold Absolute Pressure (MAP) Sensor
Manufacturer Warranty1 Year
Number of pins3-Pin
Connector Shapeoval
Pressure Range10 kPa - 115 kPa
Number of mounting bores1
Fitment TypeDirect Replacement
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category