BRAND NEW *OEM Quality* MAP Sensor (Manifold Absolute Pressure Sensor) to suit Holden Rodeo TFR / RA, Frontera UES, Jackaroo / Monterey UBS and Colorado RC - petrol and diesel engines.

Check engine light on your Rodeo or Jackaroo, rough idle, or poor throttle response under load? A failed MAP sensor is a common cause on these Isuzu-platform engines. This is a direct-fit 3-pin oval connector replacement. Same-day dispatch from Melbourne.

TO SUIT

This sensor suits the Holden Rodeo TFR30 2.2L C22NE, Rodeo TFR25 / TFS25 3.2L 6VD1, Rodeo TFR26 / TFS26 3.5L 6VE1, Rodeo TFR32 / RA 2.4L Y24SE, Frontera UES30 2.2L X22SE, Frontera UES25 3.2L 6VD1, Jackaroo / Monterey UBS25 3.2L 6VD1, Jackaroo / Monterey UBS26 3.5L 6VE1, Jackaroo UBS73 3.0L 4JX1-T diesel, and Holden Colorado RC TFR32 2.4L Y24SE. Connector: 3-pin oval.

OEM PART NUMBERS

16212460
19418807
12614970
16258659
28074365

OTHER PART NUMBERS

ACDelco: 12614970
Delphi: PS10002
Goss: MP141
HELLA: 6PP 009 400-011
NGK: 93871
NTK-AU: MA0090
VEMO: V40-72-0398
WALKER PRODUCTS: 225-1024

PACKAGE INCLUDES

1 x MAP Sensor (3-pin oval connector)

ABOUT THIS SENSOR

The Manifold Absolute Pressure (MAP) sensor measures air pressure inside the intake manifold and sends this signal to the ECU. The ECU uses it to calculate engine load and determine the correct fuel and ignition timing. On the Isuzu-platform engines used in the Holden Rodeo, Frontera, Jackaroo and Colorado the sensor is located on the intake manifold and is a straightforward plug-and-play replacement.

A failing MAP sensor causes the ECU to miscalculate fuelling - leading to rough idle, hesitation under load, excessive fuel consumption or a P0106 / P0107 / P0108 fault code. On high-mileage work vehicles like the Rodeo and Jackaroo this sensor is a known wear item.

COMMON SYMPTOMS OF FAILURE

Check engine light - fault codes P0106 / P0107 / P0108 (MAP Sensor Circuit)
Rough idle or engine hunting under load
Poor throttle response or hesitation during acceleration
Black smoke from exhaust under load
Increased fuel consumption
Engine stalling at idle

[06/98 - 02/03] HOLDEN RODEO TFR30 i (2.2L 4cyl C22NE 87kW)
[02/98 - 02/03] HOLDEN RODEO TFR25 i RWD (3.2L V6 6VD1 140kW)
[02/98 - 02/03] HOLDEN RODEO TFS25 i AWD (3.2L V6 6VD1 140kW)
[02/03 - 12/05] HOLDEN RODEO TFR26 i RWD (3.5L V6 6VE1 147kW)
[02/03 - 12/05] HOLDEN RODEO TFS26 i AWD (3.5L V6 6VE1 147kW)
[02/03 - 07/08] HOLDEN RODEO TFR32 / RA i (2.4L 4cyl Y24SE / C24SE 94kW)
[02/99 - 07/02] HOLDEN FRONTERA UES30 i (2.2L 4cyl X22SE 96kW)
[02/99 - 04/04] HOLDEN FRONTERA UES25 i (3.2L V6 6VD1 151kW)
[04/92 - 02/98] HOLDEN JACKAROO / MONTEREY UBS25 i (3.2L V6 6VD1 130kW)
[03/98 - 09/04] HOLDEN JACKAROO / MONTEREY UBS26 RS (3.5L V6 6VE1 158kW)
[03/98 - 09/04] HOLDEN JACKAROO / MONTEREY UBS73 TD (3.0L 4cyl 4JX1-T 117kW)
[07/08 - 12/12] HOLDEN COLORADO RC TFR32 i (2.4L 4cyl Y24SE 92kW)

What fault codes does a faulty MAP sensor trigger?

A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.

How do I test a MAP sensor?

With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.

Can I drive with a faulty MAP sensor?

You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.

What does a MAP sensor do?

The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.

What are the symptoms of a faulty MAP sensor?

Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.

What is the difference between a MAP sensor and a MAF sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.

Identification
SKU	CMS210-3
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CMS210-3
Reference OEM Number	16212460
Other OEM Numbers	16212460, 19418807, 12614970, 16258659, 28074365
Related Part Numbers	CMS210, MAP-005, MP141, TMP003, MA0090, AS60
Trade Part Numbers	ACDelco: 12614970, Delphi: PS10002, Goss: MP141, NTK-AU: MA0090
Product Specifics
Product Type	SENSOR
Sensor Type	Manifold Absolute Pressure (MAP) Sensor
Features	Direct Fit
Manufacturer Warranty	1 Year
Compatible Vehicles	HOLDEN RODEO TFR RA / FRONTERA UES / JACKAROO MONTEREY UBS / COLORADO RC
Number of pins	3 -pin connector
Connector Shape	oval
Supplementary Article Info	without integrated air temperature sensor
Pressure Range	20 kPa, until 100 kPa
Number of mounting bores	1
Other Details
Note	Always verify fitment using your vehicle's OEM part number.