MAP Sensor for BMW 3 Series E46 E90 E91 E92 E93 320i 325i 330i
OEM Spec Fit Replaces 13627542623
BRAND NEW *OEM Quality* MAP sensor to suit BMW 3 Series E90 E91 E92 E93 and E46 petrol engines.
Rough idle, hesitation off the line and a check engine light on an E90 usually trace back to a tired manifold pressure sensor. This is a direct plug-in replacement, dispatched same-day before 12pm.
TO SUIT
Fits the E90 sedan, E91 touring, E92 coupe and E93 convertible from 2004 to 2013 across the 318i, 320i, 323i, 325i, 330i and 335i, plus the earlier E46 316ti, 318i, 318Ci, 318ti and 323i from 2001. Covers N42, N43, N46, N52, N53, N54 and N55 engines.
OEM PART NUMBERS
- 13627542623
- 13620414704
- 13627585278
- 13628617097
- 13628657300
- 13620151009
- 13627503208
OTHER PART NUMBERS
- V20-72-5288
- ECM-BM-005
- PS20095-12B1
- 225-1179
- 15204
- 08.17.024
PACKAGE INCLUDES
1 x manifold absolute pressure sensor with 3-pin D-shaped connector and seal ring.
ABOUT THIS SENSOR
The MAP sensor reports intake manifold pressure to the DME so it can calculate air mass and set fuelling and ignition timing. On the N43 and N53 lean-burn engines fitted to later E90 and E91 models, the DME leans on this signal heavily during stratified charge operation.
When the sensor drifts, the DME fuels against a false load reading. On N46 four-cylinder cars that shows up as a lumpy cold idle; on N52 and N53 six-cylinder cars it more often appears as flat mid-range response and a slow-building misfire count.
COMMON SYMPTOMS OF FAILURE
- Check engine light with codes P0105 P0106 P0107 or P0108
- BMW-specific fault codes 2FBA 2FBB or 29CD stored in the DME
- Rough or hunting idle when cold, particularly on N46 engines
- Hesitation and flat throttle response through the mid range
- Increased fuel consumption with no other obvious cause
- Failed emissions test or intermittent limp mode
- [04/92 - 12/95] BMW 3 E36 318 is (1.8L 4cyl M42 B18 (184S1) 103kW)
- [01/96 - 08/98] BMW 3 E36 323 i (2.5L 6cyl M52 B25 (256S3) 125kW)
- [01/96 - 11/98] BMW 3 E36 323 i (2.5L 6cyl M52 B25 (256S3) 125kW)
- [10/01 - 02/05] BMW 3 E46 316 ti (1.8L 4cyl N46 B18 A,N42 B18 A 85kW)
- [09/01 - 02/04] BMW 3 E46 318 Ci (2.0L 4cyl N42 B20 A 105kW)
- [03/04 - 05/06] BMW 3 E46 318 Ci (2.0L 4cyl N46 B20 A,N46 B20 C 110kW)
- [09/01 - 02/05] BMW 3 E46 318 i (2.0L 4cyl N42 B20 A,N46 B20 A,N46 B20 C 105kW) - build from 07/2004
- [02/02 - 12/04] BMW 3 E46 318 ti (2.0L 4cyl N42 B20 A,N46 B20 A 105kW)
- [04/00 - 09/00] BMW 3 E46 323 Ci (2.5L 6cyl M52 B25 (256S4) 125kW)
- [04/99 - 09/00] BMW 3 E46 323 Ci (2.5L 6cyl M52 B25 (256S4) 125kW)
- [03/98 - 09/00] BMW 3 E46 323 i (2.5L 6cyl M52 B25 (256S4) 125kW)
- [09/05 - 08/07] BMW 3 E90 318 i (2.0L 4cyl N46 B20 B 95kW)
- [09/07 - 10/11] BMW 3 E90 320 i (2.0L 4cyl N43 B20 A 125kW)
- [12/04 - 08/07] BMW 3 E90 320 i (2.0L 4cyl N46 B20 B 110kW)
- [09/05 - 02/07] BMW 3 E90 323 i (2.5L 6cyl N52 B25 A,N52 B25 B,N52 B25 BF,N52 B25 BE 130kW) - build to 06/2009
- [03/07 - 12/11] BMW 3 E90 323 i (2.5L 6cyl N52 B25 A,N52 B25 BF 140kW) - build to 06/2009
- [12/04 - 12/11] BMW 3 E90 325 i (2.5L 6cyl N52 B25 A,N52 B25 B,N52 B25 BF 160kW)
- [12/04 - 10/11] BMW 3 E90 330 i (3.0L 6cyl N52 B30 BF,N52 B30 A 190kW)
- [09/06 - 12/11] BMW 3 E90 335 i (3.0L 6cyl N55 B30 A,N54 B30 A 225kW)
- [02/07 - 12/12] BMW 3 E91 320 i (2.0L 4cyl N43 B20 A 125kW)
- [09/05 - 06/12] BMW 3 E91 320 i (2.0L 4cyl N46 B20 B,N46 B20 BD,N46 B20 C 115kW)
- [09/05 - 06/12] BMW 3 E91 320 i (2.0L 4cyl N46 B20 B,N46 B20 C 110kW)
- [04/06 - 06/07] BMW 3 E91 323 i (2.5L 6cyl N52 B25 A 130kW)
- [09/06 - 12/12] BMW 3 E91 323 i (2.5L 6cyl N52 B25 A 140kW)
- [12/04 - 08/08] BMW 3 E91 325 i (2.5L 6cyl N52 B25 A 160kW)
- [08/05 - 08/07] BMW 3 E91 330 i (3.0L 6cyl N52 B30 A 190kW)
- [03/07 - 12/12] BMW 3 E92 320 i (2.0L 4cyl N43 B20 A 125kW)
- [04/06 - 02/12] BMW 3 E92 323 i (2.5L 6cyl N52 B25 AE,N52 B25 BE 140kW)
- [06/06 - 02/10] BMW 3 E92 325 i (2.5L 6cyl N52 B25 A,N52 B25 AF,N52 B25 BF 160kW)
- [03/10 - 12/12] BMW 3 E92 330 i (3.0L 6cyl N52 B30 A 190kW)
- [09/06 - 02/10] BMW 3 E92 330 i (3.0L 6cyl N52 B30 BF,N52 B30 A,N52 B30 AF 200kW)
- [06/06 - 12/12] BMW 3 E92 335 i (3.0L 6cyl N55 B30 A,N54 B30 A 225kW)
- [03/07 - 12/12] BMW 3 E93 320 i (2.0L 4cyl N43 B20 A 125kW)
- [12/06 - 02/10] BMW 3 E93 325 i (2.5L 6cyl N52 B25 A 160kW)
- [12/06 - 12/12] BMW 3 E93 335 i (3.0L 6cyl N55 B30 A,N54 B30 A 225kW)
What fault codes does a faulty MAP sensor trigger?
A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.
How do I test a MAP sensor?
With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.
Can I drive with a faulty MAP sensor?
You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.
What does a MAP sensor do?
The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.
What are the symptoms of a faulty MAP sensor?
Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.
What is the difference between a MAP sensor and a MAF sensor?
A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SCMS288 |
| Reference OEM Number | 13627542623 |
| Other OEM Numbers | 13620414704, 13627542623, 13627585278, 13628617097, 13628657300 |
| Related Part Numbers | CMS288, MAP-180, MP208, OMS288 |
| Interchange Part Numbers | V20-72-5288, ECM-BM-005, PS20095-12B1 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Manifold Absolute Pressure (MAP) Sensor |
| Manufacturer Warranty | 1 Year |
| Fitting Position | Fits On Intake Manifold |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Number of mounting bores | 2 |
| Compatible Makes | BMW |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.