





1-Bar MAP Sensor for HSV Commodore Clubsport Maloo Senator 5.0L V8 16137039
Direct Fit Replaces 16017460 16137039
BRAND NEW *OEM Quality* 1-Bar MAP Sensor to suit HSV Clubsport / Maloo / Senator / Grange / GTS and Holden Commodore / Berlina / Calais / Statesman / Caprice VN VP VR VS VT with 5.0L V8 and 3.8L V6 engines.
If your Holden or HSV is running rough at idle, hunting for fuel trim, or showing fault code P0107 - a failed MAP sensor is one of the first things to check. This is a direct-fit 1-Bar replacement for the factory Delco ECU. Ships same-day from Cranbourne VIC.
TO SUIT
Suits HSV Clubsport VP VR VS VT / Maloo VG VP VR VS / Senator VP VR VS VT / Grange VS / GTS VR VS and Holden Commodore / Berlina / Calais / Statesman / Caprice VN VP VR VS VT with the 5.0L V8 (GMH304 / GMH308 / VU engine codes) and 3.8L V6 (LG2 / LN3 / L27) from 1988 to 1999. Also suits the 3.3L 202 cu.in Black engine in the VK series from 1984 to 1986.
FITMENT CHECK
This sensor is rated for naturally aspirated 1-Bar applications only. It is not suitable for aftermarket forced induction setups requiring a 2-Bar or 3-Bar sensor, and it must NOT be fitted to the factory Supercharged L67 3.8L V6 (VS Series II Commodore, Calais, Statesman, Caprice) - those require a 2-Bar sensor (Part No. 16040609). If your engine has been supercharged or turbocharged after factory build, verify your boost range before ordering.
OEM PART NUMBERS
- 16137039
- 16017460
- 12569240
- 8161370390
- 1144809
- 1C1Y9F479AA
OTHER PART NUMBERS
- BOSCH: F 000 99P 169
- DELPHI: PS10075-15B1
- WALKER PRODUCTS: 225-1001
- VEMO: V40-72-0323
PACKAGE INCLUDES
1 x 1-Bar MAP Sensor. 3-pin rectangular connector. Direct plug-in replacement - no wiring modification required.
ABOUT THIS SENSOR
The Manifold Absolute Pressure (MAP) sensor measures intake manifold vacuum and reports it to the ECU to calculate the correct fuel injection and ignition timing. On the Delco MPFI system used across the VN through VT range, accurate MAP data is essential - an out-of-spec reading causes the ECU to run rich or lean, often creating rough idle, hesitation under load, and increased fuel consumption.
This sensor is calibrated to the 1-Bar (0-100 kPa) curve required by the factory Delco ECU. Running a 2-Bar or 3-Bar sensor on a naturally aspirated engine will cause incorrect fuelling and may trigger continuous fault codes.
COMMON SYMPTOMS OF FAILURE
- Rough idle or engine hunting
- Hesitation or flat spot under acceleration
- Higher than normal fuel consumption
- Check engine light with codes P0107 / P0108 / P0106
- Black exhaust smoke (running rich)
- Engine stalls at idle
- [1994 - 1995] HSV CAPRICE VR 5.7L 8cyl HSVV8 215kW (Sedan)
- [1995 - 1996] HSV CAPRICE VS 5.7L 8cyl HSVV8 215kW (Sedan)
- [1991 - 1993] HSV CLUBSPORT VP 5.0L 8cyl VU 180kW (Sedan)
- [1993 - 1995] HSV CLUBSPORT VR 5.0L 8cyl GMH308 185kW (Sedan)
- [1993 - 1995] HSV CLUBSPORT VR 5.0L 8cyl GMH308 185kW (Wagon)
- [1995 - 1997] HSV CLUBSPORT VS 5.0L 8cyl GMH308 185kW (Sedan)
- [1995 - 1997] HSV CLUBSPORT VS 5.0L 8cyl GMH308 185kW (Wagon)
- [1997 - 1999] HSV CLUBSPORT VT 5.0L 8cyl GMH308 195kW (Sedan)
- [1989 - 1991] HSV COMMODORE VN 3.8L 6cyl LN3 125kW (Sedan)
- [1989 - 1991] HSV COMMODORE VN 3.8L 6cyl LN3 132kW (Sedan)
- [1989 - 1990] HSV COMMODORE VN 5.0L 8cyl GMH308 180kW (Sedan)
- [1989 - 1991] HSV COMMODORE VN 5.0L 8cyl GMH308 200kW (Sedan)
- [1989 - 1991] HSV COMMODORE VN 5.0L 8cyl GMH308 210kW (Sedan)
- [1992 - 1993] HSV COMMODORE VP 3.8L 6cyl LN3 125kW (Sedan)
- [1994 - 1995] HSV GTS VR 5.7L 8cyl HSVV8 215kW (Sedan)
- [1995 - 1997] HSV GTS VS 5.7L 8cyl HSVV8 215kW (Sedan)
- [1996 - 1999] HSV GRANGE VS 5.0L 8cyl VU 185kW (Sedan)
- [1996 - 1999] HSV GRANGE VS 5.7L 8cyl HSVV8 215kW (Sedan)
- [1998 - 1999] HSV GRANGE VS 5.0L 8cyl VU 195kW (Sedan)
- [1991 - 1992] HSV LS VG 3.8L 6cyl LN3 125kW (Ute)
- [1991 - 1992] HSV LS VG 5.0L 8cyl VU 165kW (Ute)
- [1992 - 1993] HSV LS VP 3.8L 6cyl LN3 127kW (Ute)
- [1992 - 1993] HSV LS VP 5.0L 8cyl VU 180kW (Ute)
- [1990 - 1992] HSV MALOO VG 5.0L 8cyl VU 180kW (Ute)
- [1992 - 1993] HSV MALOO VP 5.0L 8cyl VU 180kW (Ute)
- [1993 - 1995] HSV MALOO VR 5.0L 8cyl VU 185kW (Ute)
- [1995 - 1999] HSV MALOO VS 5.0L 8cyl VU 185kW (Ute)
- [1995 - 2000] HSV MALOO VS 5.0L 8cyl VU 195kW (Ute)
- [1995 - 1997] HSV MANTA VS 5.0L 8cyl VU 185kW (Sedan)
- [1995 - 1997] HSV MANTA VS 5.0L 8cyl VU 185kW (Wagon)
- [1997 - 1999] HSV MANTA VT 5.0L 8cyl VU 195kW (Sedan)
- [1992 - 1993] HSV SENATOR VP 5.0L 8cyl VU 180kW (Sedan)
- [1992 - 1993] HSV SENATOR VR 5.0L 8cyl VU 185kW (Sedan)
- [1993 - 1995] HSV SENATOR VR 5.7L 8cyl HSVV8 215kW (Sedan)
- [1995 - 1997] HSV SENATOR VS 5.0L 8cyl VU 185kW (Sedan)
- [1995 - 1997] HSV SENATOR VS 5.7L 8cyl HSVV8 215kW (Sedan)
- [1997 - 1999] HSV SENATOR VT 5.0L 8cyl VU 195kW (Sedan)
- [1997 - 2000] HSV SENATOR VT 5.0L 8cyl VU 195kW (Wagon)
- [1990 - 1993] HSV STATESMAN VQ 5.0L 8cyl GMH308 180kW (Sedan)
- [1991 - 1993] HSV STATESMAN VQ 5.0L 8cyl GMH308 200kW (Sedan)
- [1994 - 1995] HSV STATESMAN VR 5.0L 8cyl GMH308 185kW (Sedan)
- [1994 - 1995] HSV STATESMAN VR 5.7L 8cyl HSVV8 215kW (Sedan)
- [1995 - 1996] HSV STATESMAN VS 5.0L 8cyl GMH308 185kW (Sedan)
- [1995 - 1996] HSV STATESMAN VS 5.7L 8cyl HSVV8 215kW (Sedan)
- [1999 - 1999] HSV XU8 VT 5.0L 8cyl VU 195kW (Sedan)
- [1994 - 1997] HOLDEN BARINA SB 1.2L 4cyl C 12 NZ 33kW (Hatchback)
- [1994 - 1997] HOLDEN BARINA SB 1.4L 4cyl C 14 NZ 44kW (Hatchback)
- [1994 - 1998] HOLDEN BARINA SB 1.6L 4cyl X 16 XE 78kW (Hatchback)
- [1997 - 2000] HOLDEN BARINA SB 1.4L 4cyl C 14 SE 60kW (Convertible)
- [1997 - 2001] HOLDEN BARINA SB 1.4L 4cyl C 14 SE 60kW (Hatchback)
- [1986 - 1988] HOLDEN BERLINA VL 4.9L 8cyl GMH 304 (Black) 122kW (Sedan)
- [1986 - 1988] HOLDEN BERLINA VL 4.9L 8cyl GMH 304 (Black) 122kW (Wagon)
- [1988 - 1991] HOLDEN BERLINA VN 3.8L 6cyl LG2,LN3 125kW (Sedan)
- [1988 - 1991] HOLDEN BERLINA VN 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1988 - 1991] HOLDEN BERLINA VN 3.8L 6cyl LG2,LN3 125kW (Wagon)
- [1988 - 1991] HOLDEN BERLINA VN 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1991 - 1993] HOLDEN BERLINA VP 3.8L 6cyl LG2,L27 127kW (Sedan)
- [1991 - 1993] HOLDEN BERLINA VP 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1991 - 1993] HOLDEN BERLINA VP 3.8L 6cyl LG2,L27 127kW (Wagon)
- [1991 - 1993] HOLDEN BERLINA VP 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1993 - 1995] HOLDEN BERLINA VR 3.8L 6cyl LG2,L27 130kW (Sedan)
- [1993 - 1995] HOLDEN BERLINA VR 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1993 - 1995] HOLDEN BERLINA VR 3.8L 6cyl LG2,L27 130kW (Wagon)
- [1993 - 1995] HOLDEN BERLINA VR 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1995 - 1997] HOLDEN BERLINA VS 3.8L 6cyl LG2 147kW (Sedan)
- [1995 - 1997] HOLDEN BERLINA VS 5.0L 8cyl GMH 304 (Black) 168kW (Sedan)
- [1995 - 1997] HOLDEN BERLINA VS 3.8L 6cyl LG2 147kW (Wagon)
- [1995 - 1997] HOLDEN BERLINA VS 5.0L 8cyl GMH 304 (Black) 168kW (Wagon)
- [1997 - 1999] HOLDEN BERLINA VT 5.0L 8cyl GMH 304 (Black) 179kW (Sedan)
- [1997 - 1999] HOLDEN BERLINA VT 5.0L 8cyl GMH 304 (Black) 179kW (Wagon)
- [1986 - 1988] HOLDEN CALAIS VL 5.0L 8cyl GMH 304 (Black) 122kW (Sedan)
- [1988 - 1988] HOLDEN CALAIS VL 5.0L 8cyl GMH 304 (Black) 122kW (Wagon)
- [1988 - 1990] HOLDEN CALAIS VN 3.8L 6cyl LG2,LN3 125kW (Sedan)
- [1989 - 1990] HOLDEN CALAIS VN 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1991 - 1993] HOLDEN CALAIS VP 3.8L 6cyl LG2,L27 127kW (Sedan)
- [1991 - 1993] HOLDEN CALAIS VP 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1993 - 1995] HOLDEN CALAIS VR 3.8L 6cyl LG2,L27 130kW (Sedan)
- [1993 - 1994] HOLDEN CALAIS VR 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1995 - 1997] HOLDEN CALAIS VS 3.8L 6cyl LG2 147kW (Sedan)
- [1995 - 1996] HOLDEN CALAIS VS 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1997 - 1997] HOLDEN CALAIS VS 5.0L 8cyl GMH 304 (Black) 168kW (Sedan)
- [1997 - 1999] HOLDEN CALAIS VT 5.0L 8cyl GMH 304 (Black) 179kW (Sedan)
- [1998 - 1999] HOLDEN CALAIS VT 5.0L 8cyl GMH 304 (Black) 195kW (Sedan)
- [1986 - 1987] HOLDEN CAMIRA JD 1.8L 4cyl 18JC 63kW (Sedan)
- [1986 - 1987] HOLDEN CAMIRA JD 1.8L 4cyl 18JC 63kW (Wagon)
- [1987 - 1989] HOLDEN CAMIRA JE 2.0L 4cyl C 20 JE 85kW (Sedan)
- [1987 - 1989] HOLDEN CAMIRA JE 2.0L 4cyl C 20 JE 85kW (Wagon)
- [1990 - 1994] HOLDEN CAPRICE VQ 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1994 - 1994] HOLDEN CAPRICE VR 3.8L 6cyl LG2,L27 130kW (Sedan)
- [1994 - 1995] HOLDEN CAPRICE VR 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1995 - 1998] HOLDEN CAPRICE VS 3.8L 6cyl LG2 147kW (Sedan)
- [1995 - 1999] HOLDEN CAPRICE VS 5.0L 8cyl GMH 304 (Black) 168kW (Sedan)
- [1996 - 1997] HOLDEN COMBO SB 1.4L 4cyl C 14 NZ 44kW (Van)
- [1997 - 2002] HOLDEN COMBO SB 1.4L 4cyl C 14 SE 60kW (Van)
- [1986 - 1988] HOLDEN COMMODORE VL 4.9L 8cyl GMH 304 (Black) 122kW (Sedan)
- [1986 - 1987] HOLDEN COMMODORE VL 4.9L 8cyl GMH 304 (Black) 196kW (Sedan)
- [1986 - 1988] HOLDEN COMMODORE VL 4.9L 8cyl GMH 304 (Black) 122kW (Wagon)
- [1988 - 1991] HOLDEN COMMODORE VG 3.8L 6cyl LG2,L27 125kW (Ute)
- [1988 - 1991] HOLDEN COMMODORE VN 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1988 - 1991] HOLDEN COMMODORE VN 3.8L 6cyl LG2,LN3 125kW (Wagon)
- [1988 - 1991] HOLDEN COMMODORE VN 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1990 - 1991] HOLDEN COMMODORE VG 3.8L 6cyl LG2,LN3 127kW (Ute)
- [1990 - 1991] HOLDEN COMMODORE VN 3.8L 6cyl LG2,LN3 125kW (Sedan)
- [1991 - 1993] HOLDEN COMMODORE VP 3.8L 6cyl LG2,L27 127kW (Sedan)
- [1991 - 1993] HOLDEN COMMODORE VP 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1991 - 1993] HOLDEN COMMODORE VP 3.8L 6cyl LG2,L27,LN3 127kW (Ute)
- [1991 - 1993] HOLDEN COMMODORE VP 5.0L 8cyl GMH 304 (Black) 165kW (Ute)
- [1991 - 1993] HOLDEN COMMODORE VP 3.8L 6cyl LG2,L27 127kW (Wagon)
- [1991 - 1993] HOLDEN COMMODORE VP 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1993 - 1995] HOLDEN COMMODORE VR 3.8L 6cyl LG2,L27 130kW (Sedan)
- [1993 - 1995] HOLDEN COMMODORE VR 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1993 - 1995] HOLDEN COMMODORE VR 3.8L 6cyl LG2,L27 130kW (Ute)
- [1993 - 1995] HOLDEN COMMODORE VR 5.0L 8cyl GMH 304 (Black) 165kW (Ute)
- [1993 - 1995] HOLDEN COMMODORE VR 3.8L 6cyl LG2,L27 130kW (Wagon)
- [1993 - 1995] HOLDEN COMMODORE VR 5.0L 8cyl GMH 304 (Black) 165kW (Wagon)
- [1995 - 1997] HOLDEN COMMODORE VS 3.8L 6cyl LG2 147kW (Sedan)
- [1995 - 1997] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1995 - 2000] HOLDEN COMMODORE VS 3.8L 6cyl LG2 147kW (Ute)
- [1995 - 1996] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 165kW (Ute)
- [1995 - 1997] HOLDEN COMMODORE VS 3.8L 6cyl LG2 147kW (Wagon)
- [1995 - 1997] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 167kW (Wagon)
- [1996 - 1997] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 168kW (Sedan)
- [1996 - 2000] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 168kW (Ute)
- [1997 - 2000] HOLDEN COMMODORE VS 5.0L 8cyl GMH 304 (Black) 179kW (Ute)
- [1997 - 1999] HOLDEN COMMODORE VT 5.0L 8cyl GMH 304 (Black) 179kW (Sedan)
- [1997 - 1999] HOLDEN COMMODORE VT 5.0L 8cyl GMH 304 (Black) 179kW (Wagon)
- [1998 - 1999] HOLDEN COMMODORE VT 5.0L 8cyl GMH 304 (Black) 195kW (Sedan)
- [1992 - 1998] HOLDEN JACKAROO / MONTEREY UBS 3.2L 6cyl 6VD1 (SOHC) 130kW (SUV)
- [1998 - 2004] HOLDEN JACKAROO / MONTEREY UBS 3.0L 4cyl 4JX1-T 117kW (SUV)
- [1990 - 1993] HOLDEN STATESMAN VQ 3.8L 6cyl LG2,L27 127kW (Sedan)
- [1990 - 1994] HOLDEN STATESMAN VQ 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1994 - 1995] HOLDEN STATESMAN VR 3.8L 6cyl LG2,L27 130kW (Sedan)
- [1994 - 1995] HOLDEN STATESMAN VR 5.0L 8cyl GMH 304 (Black) 165kW (Sedan)
- [1995 - 1999] HOLDEN STATESMAN VS 3.8L 6cyl LG2,LN3 147kW (Sedan)
- [1995 - 1999] HOLDEN STATESMAN VS 5.0L 8cyl GMH 304 (Black) 168kW (Sedan)
What fault codes does a faulty MAP sensor trigger?
A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.
How do I test a MAP sensor?
With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.
Can I drive with a faulty MAP sensor?
You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.
What does a MAP sensor do?
The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.
What are the symptoms of a faulty MAP sensor?
Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.
What is the difference between a MAP sensor and a MAF sensor?
A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.
| Identification | |
|---|---|
| SKU | CMS206-HSV |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CMS206 |
| Reference OEM Number | 16137039 |
| Other OEM Numbers | 16137039, 16017460, 8161370390, 12569240, 1144809, 1C1Y9F479AA |
| Related Part Numbers | CMS206, MP107, MAP-002, ACDelco: 213-1545 |
| Trade Part Numbers | BOSCH: F 000 99P 169, VEMO: V40-72-0323, DELPHI: PS10075-15B1 |
| Product Specifics | |
| Sensor Type | Manifold Absolute Pressure Sensor |
| Type | MAP Sensor |
| Number of pins | 3-Pin |
| Connector Shape | rectangular |
| Pressure Range | 26 kPa to 100 kPa |
| Compatible Makes | Holden / HSV |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | 1-Bar only - not for Supercharged L67 (use 16040609) |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.