BRAND NEW *OEM Quality* MAF sensor to suit Nissan Navara D40 and D22 with the 2.5L YD25 common-rail diesel, plus the D40 4.0L V6.

If your Navara has dropped into limp mode, lost its pull or started blowing black smoke, a failing MAF is one of the first things to check on the YD25. This heavy duty fit replacement restores power and is dispatched from Melbourne.

TO SUIT

Fits the Navara D40 2.5L YD25DDTi dCi diesel from late 2005 to 2015 across the 106kW, 126kW, 128kW and 140kW (D40T) tunes, plus the D22 with the 2.5L YD25DDTi. It also suits the D40 4.0L VQ40 V6 petrol from 2005 to 2011. Year-by-year coverage is in the compatibility table.

FITMENT CHECK

D22 models must have the 2.5L YD25 engine - the older 3.0L ZD30 D22 is not listed for this part. Insert only, fits your original housing. Match OEM 22680-7S000 or 22680-7S00A before ordering.

OEM PART NUMBERS

22680-7S000
22680-7S00A
22680-7S00B
22680-AW400
226807F408

OTHER PART NUMBERS

0986JG1618
V38-72-0006-1
AFT6-V011
DMA-0203
AFH70M38
2910000438300
EPP-NS-007
7.22184.43.0
245-1117

PACKAGE INCLUDES

1 x BRAND NEW mass airflow sensor - insert only (fits your original intake housing), 5-pin oval connector, 12V.

ABOUT THIS SENSOR

On the YD25 the MAF reading controls far more than fuelling - the ECU also uses it to set EGR flow and turbo boost. A contaminated or drifting sensor under-reads airflow, the engine overfuels and the ECU pulls power to protect itself, which is why limp mode is so common on high-kilometre D40s.

Many owners replace turbos, EGR valves or injectors before checking the MAF. A fresh sensor is a low-cost first step and has a low return rate.

COMMON SYMPTOMS OF FAILURE

Check engine light - fault codes P0100 P0101 P0102 P0103 (MAF circuit)
Limp mode or sudden loss of power under load
Black smoke when accelerating or towing
Turbo lag or flat spot off idle
Rough idle and stalling
Increased fuel consumption

[02/02 - 02/15] NISSAN NAVARA D22 Di 2.5L 4cyl YD25DDTi 98kW
[02/02 - 02/15] NISSAN NAVARA D22 Di 2.5L 4cyl YD25DDTi/ YD25ETI 98kW
[03/02 - 02/15] NISSAN NAVARA D22 dCi 2.5L 4cyl YD25DDTi 98kW
[12/05 - 01/13] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 128kW
[12/05 - 06/11] NISSAN NAVARA D40 4.0L V6 VQ40 198kW
[12/05 - 11/09] NISSAN NAVARA D40 4.0L V6 VQ40 198kW
[01/07 - 10/15] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 126kW
[07/08 - 04/15] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 106kW
[08/08 - 10/15] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 126kW
[11/09 - 10/15] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 106kW
[05/10 - 04/15] NISSAN NAVARA D40 dCi 2.5L 4cyl YD25DDTi 120kW
[05/10 - 04/15] NISSAN NAVARA D40T dCi 2.5L 4cyl YD25DDTi 140kW

Can I clean my MAF sensor instead of replacing it?

Yes - if the sensor is contaminated rather than electrically failed, cleaning with a dedicated MAF sensor cleaner spray can restore correct readings. Do not use brake cleaner or generic electrical contact cleaner as these leave residue that damages the sensing wire. Allow the sensor to dry completely before reinstalling. If cleaning does not resolve the fault codes, the sensor requires replacement.

What is the difference between a MAF sensor and a MAP sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine using a hot wire element in the intake. A MAP (Manifold Absolute Pressure) sensor measures intake manifold pressure to calculate air density. Most modern engines use one or the other - some use both. Your vehicle service manual or OBD2 fault codes will confirm which sensor type your engine uses.

Will a faulty MAF sensor cause my vehicle to fail an emissions test?

Yes. A faulty MAF sensor causes the ECU to miscalculate fuel delivery, typically resulting in a rich running condition that increases CO and hydrocarbon emissions. Most roadworthy and emissions checks will fail a vehicle with an active MAF sensor fault code or visibly excessive exhaust smoke.

What are the symptoms of a bad MAF sensor?

Common symptoms include rough idle, hesitation or stumbling on acceleration, poor fuel economy, black smoke from the exhaust, and an illuminated Check Engine light. Your ECU may log fault codes P0100 to P0104.

Can I drive with a faulty MAF sensor?

You can drive short distances but it is not recommended. A faulty MAF sensor causes the ECU to run incorrect fuel mixtures, which can damage the catalytic converter and O2 sensors over time. Have it replaced as soon as possible.

How do I test if my MAF sensor is bad?

Use an OBD2 scanner to check for fault codes P0100-P0104. You can also use a multimeter or live data scanner to check the sensor output voltage against your vehicle's specification. A reading significantly outside spec confirms a faulty sensor.

What causes a MAF sensor to fail?

The most common causes are a dirty or contaminated sensing element (often from a missing or damaged air filter), oil contamination from an over-oiled aftermarket air filter, heat damage, or general wear over time.

Do I need to reset my ECU after replacing the MAF sensor?

It is good practice to clear any stored fault codes using an OBD2 scanner after replacement. Some vehicles will self-adapt within a short drive cycle, but clearing codes ensures the ECU recalibrates from a clean baseline.

Identification
SKU	CAF083-Navara
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CAF083
Reference OEM Number	22680-7S00A
Other OEM Numbers	226807S000, 22680-7S000, 22680-7S00B, 22680-AW400
Related Part Numbers	AFM-128, AM7S000N, TAF003
Trade Part Numbers	0986JG1618, DMA-0203
Product Specifics
Product Type	SENSOR
Sensor Type	Mass Airflow Sensor
Number of pins	5
Connector Shape	oval
Voltage	12 V
Housing Type	without housing
Compatible Makes	Nissan
Fitment Type	Direct Replacement
Other Details
Note	Always verify fitment using your vehicle's OEM part number.