DPF Exhaust Pressure Sensor for Holden Cruze JG Epica EP 2.0L Z20S1 Diesel
Direct Fit Replaces 96419104
BRAND NEW *OEM Quality* DPF exhaust pressure sensor to suit Holden Cruze JG and Epica EP 2.0L Z20S1 diesel.
A Cruze or Epica diesel that shows a DPF warning, or feels flat when you put your foot down, may only need a new pressure sensor. It is a cheap first fix before a filter replacement. Packed and shipped from Cranbourne VIC.
TO SUIT
Holden Cruze JG DTFi sedan with the 2.0L Z20S1 diesel (110kW), 06/2009 to 03/2011, and Epica EP TD sedan with the 2.0L Z20S1 diesel (110kW), 07/2008 to 12/2011, all with a factory fitted DPF.
FITMENT CHECK
Factory DPF models only. Compare the sensor image and the OEM number printed on your original sensor before ordering. This sensor has a 3-pin D-shape connector and 2 mounting bores. It is supplied without a fastening clamp or holding frame.
OEM PART NUMBERS
- 96419104
- 25182883
- 4818222
- 96436559
- 96436548
- 96832661
OTHER PART NUMBERS
- 0986280724
- V40-72-0639
- EPD3-D031
- ECS-DW-000
PACKAGE INCLUDES
1 x DPF differential pressure sensor with 3-pin D-shape connector. The fastening clamp, holding frame and pressure hoses are not included.
ABOUT THIS SENSOR
The sensor reads the pressure difference across the particulate filter so the engine computer can judge soot load and time each regen on the 2.0L Z20S1 diesel.
A false reading leads to missed or repeated regens and, over time, a blocked filter. Fault codes P2452 to P2455 point at this circuit.
COMMON SYMPTOMS OF FAILURE
- DPF or engine warning light
- Limp mode and flat acceleration
- Regens too often or never finishing
- Higher fuel consumption
- Fault codes P2452 P2453 P2454 P2455
- [06/09 - 03/11] HOLDEN CRUZE JG DTFi (2.0L 4cyl Z20S1 110kW, Sedan FWD)
- [07/08 - 12/11] HOLDEN EPICA EP TD (2.0L 4cyl Z20S1 110kW, Sedan FWD)
What is the difference between a DPF differential pressure sensor and an exhaust gas temperature sensor?
The DPF differential pressure sensor measures the pressure difference across the diesel particulate filter to determine how blocked it is with soot. The exhaust gas temperature (EGT) sensor measures the actual temperature of exhaust gases at a specific point in the exhaust system. Both sensors are used by the ECU to manage DPF regeneration - the pressure sensor triggers regeneration when the filter is blocked, and the temperature sensor monitors whether regeneration temperatures have been reached.
What are the symptoms of a faulty DPF pressure or temperature sensor?
Both sensor types can cause similar symptoms when they fail. Common signs include a DPF warning light on the dashboard, the engine entering limp mode with restricted power, failed or incomplete DPF regeneration cycles, increased fuel consumption from excessive regeneration attempts, loss of power under acceleration, and a Check Engine light with DPF or exhaust temperature fault codes. In some cases the vehicle may be locked out of further DPF regeneration until the fault is resolved.
Will a faulty DPF sensor damage the DPF itself?
Yes - indirectly. If the DPF pressure sensor fails and prevents the ECU from triggering regeneration correctly, soot accumulation will continue unmanaged. Over time an unmanaged DPF will become completely blocked, requiring forced regeneration by a workshop or DPF replacement. Similarly a faulty EGT sensor that prevents the ECU from confirming regeneration temperatures can cause repeated incomplete regeneration attempts that accelerate DPF loading.
Can I drive with a DPF or EGT sensor fault?
Short distances only. A DPF sensor fault will typically trigger limp mode on modern diesel vehicles, restricting power significantly. Even if limp mode is not triggered, driving with an unmanaged DPF blockage risks complete filter failure. EGT sensor faults can also prevent the turbocharger from receiving correct protection data, risking turbo damage under sustained high load. Both faults should be addressed promptly.
How many EGT sensors does my vehicle have?
Most modern diesel vehicles with a DPF have two or more EGT sensors - typically one upstream of the DPF and one downstream. Some vehicles also have additional sensors before and after the turbocharger and catalytic converter. Each sensor monitors a different temperature zone and feeds separate data to the ECU. A fault code will specify which sensor position has failed. Use the Vehicle Part Finder to confirm the correct sensor for your specific mounting position.
Do DPF and EGT sensors require programming after replacement?
No programming is required. Both are direct plug-in replacement sensors. Clear stored fault codes with an OBD2 scanner after replacement. If DPF regeneration was previously prevented by the sensor fault, you may need to initiate a forced regeneration using a scan tool to clear accumulated soot before returning the vehicle to normal service.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SDP102 |
| Reference OEM Number | 96419104 |
| Other OEM Numbers | 96419104, 25182883, 4818222, 96436559, 96436548, 96832661 |
| Related Part Numbers | DEPS1024, DP101, DP102 |
| Interchange Part Numbers | 0986280724, V40-72-0639, EPD3-D031, ECS-DW-000 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | DPF Differential Pressure Sensor |
| Fitting Position | Soot Particle Filter |
| Number of pins | 3-Pin |
| Connector Shape | D-shaped |
| Exhaust System | for vehicles with factory fitted soot particulate filter |
| Number of connectors | 2 |
| Rated Voltage | 12 V |
| Pressure Range | 50000 Pa to 450000 Pa |
| Number of mounting bores | 2 |
| Number of circuits | 2 |
| Compatible Makes | Holden |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Supplied without fastening clamp or holding frame |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.