DPF Exhaust Pressure Sensor for Mercedes Benz A-Class W176 A180 CDI 1.5L
OEM Spec Fit Replaces 6079050500
BRAND NEW *OEM Quality* DPF exhaust pressure sensor to suit Mercedes Benz A-Class W176 A180 CDI 1.5L diesel.
If your A180 CDI shows a DPF warning or goes into limp mode, a failed pressure sensor is one of the cheapest things to rule out before a filter replacement. Packed and shipped from Cranbourne VIC.
TO SUIT
Mercedes Benz A-Class W176 A180 CDI hatchback with the 1.5L diesel (80kW), 2012 to 2018.
FITMENT CHECK
Compare the sensor image and the OEM number printed on your original sensor before ordering. This sensor has a 3-pin oval connector.
OEM PART NUMBERS
- 6079050500
- A6079050500
- A6229050800
OTHER PART NUMBERS
- 0261230579
- 0261230600
- 0281006328
- DPS00016
- DPS00016-15B1
- 1.993.291
- 7.11190.08.0
PACKAGE INCLUDES
1 x DPF differential pressure sensor with 3-pin oval connector. Mounting clamp and pressure hoses are not included.
ABOUT THIS SENSOR
The sensor reports the pressure drop across the particulate filter so the engine computer can judge soot load and time each regen.
On the small 1.5L diesel a false reading can trigger repeated regens that dilute the oil, so it is worth fixing early. Fault codes P2452 to P2455 point at this circuit.
COMMON SYMPTOMS OF FAILURE
- DPF or engine warning light
- Limp mode and flat acceleration
- Frequent regens with a fan running after shut down
- Rising fuel consumption
- Fault codes P2452 P2453 P2454 P2455
- [06/12 - 05/18] MERCEDES-BENZ A-CLASS W176 A 180 CDI / d 176.012 (1.5L 80kW, Hatchback)
What is the difference between a DPF differential pressure sensor and an exhaust gas temperature sensor?
The DPF differential pressure sensor measures the pressure difference across the diesel particulate filter to determine how blocked it is with soot. The exhaust gas temperature (EGT) sensor measures the actual temperature of exhaust gases at a specific point in the exhaust system. Both sensors are used by the ECU to manage DPF regeneration - the pressure sensor triggers regeneration when the filter is blocked, and the temperature sensor monitors whether regeneration temperatures have been reached.
What are the symptoms of a faulty DPF pressure or temperature sensor?
Both sensor types can cause similar symptoms when they fail. Common signs include a DPF warning light on the dashboard, the engine entering limp mode with restricted power, failed or incomplete DPF regeneration cycles, increased fuel consumption from excessive regeneration attempts, loss of power under acceleration, and a Check Engine light with DPF or exhaust temperature fault codes. In some cases the vehicle may be locked out of further DPF regeneration until the fault is resolved.
Will a faulty DPF sensor damage the DPF itself?
Yes - indirectly. If the DPF pressure sensor fails and prevents the ECU from triggering regeneration correctly, soot accumulation will continue unmanaged. Over time an unmanaged DPF will become completely blocked, requiring forced regeneration by a workshop or DPF replacement. Similarly a faulty EGT sensor that prevents the ECU from confirming regeneration temperatures can cause repeated incomplete regeneration attempts that accelerate DPF loading.
Can I drive with a DPF or EGT sensor fault?
Short distances only. A DPF sensor fault will typically trigger limp mode on modern diesel vehicles, restricting power significantly. Even if limp mode is not triggered, driving with an unmanaged DPF blockage risks complete filter failure. EGT sensor faults can also prevent the turbocharger from receiving correct protection data, risking turbo damage under sustained high load. Both faults should be addressed promptly.
How many EGT sensors does my vehicle have?
Most modern diesel vehicles with a DPF have two or more EGT sensors - typically one upstream of the DPF and one downstream. Some vehicles also have additional sensors before and after the turbocharger and catalytic converter. Each sensor monitors a different temperature zone and feeds separate data to the ECU. A fault code will specify which sensor position has failed. Use the Vehicle Part Finder to confirm the correct sensor for your specific mounting position.
Do DPF and EGT sensors require programming after replacement?
No programming is required. Both are direct plug-in replacement sensors. Clear stored fault codes with an OBD2 scanner after replacement. If DPF regeneration was previously prevented by the sensor fault, you may need to initiate a forced regeneration using a scan tool to clear accumulated soot before returning the vehicle to normal service.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SDEPS1011 |
| Reference OEM Number | 6079050500 |
| Other OEM Numbers | 6079050500, A6079050500, A6229050800 |
| Related Part Numbers | DPS00016, 0281006207, V38-72-0126, DEPS1011 |
| Interchange Part Numbers | 0281006252, 0281006207, V59-72-0003, EPD3-V012, 6PP009409-041 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | DPF Differential Pressure Sensor |
| Fitting Position | Soot Particle Filter |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Pressure Range | 100 kPa |
| Number of mounting bores | 1 |
| Number of circuits | 2 |
| Compatible Makes | Mercedes-Benz |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.