





Crankshaft Angle Sensor for Hino 300 500 Series & Toyota Dyna Coaster Trucks
Aftermarket OEM Replacement for Hino 300 500 Series
BRAND NEW OEM Quality FLYWHEEL CRANKSHAFT POSITION SENSOR TO SUIT HINO BUS RN TRUCK DUTRO DYNA COASTER
TO SUIT:
HINO BUS RN TRUCK DUTRO DYNA COASTER FD FD8J 2008- FD7J 2011-
HINO 500 SERIES FC7J FE7J FC 2011- and many more
OEM#
89411E0050, 89411-E0050, 89410.027, 90919-05005, 9091905005, 0296000570
89411.031, 894111280, 1V3904, 1V3904G, 89411-1280
PACKAGE INCLUDES:
1 X OEM Quality FLYWHEEL / CRANKSHAFT POSITION SENSOR (2-PIN PLUG)
The crankshaft position sensor is an engine management component found on virtually all modern vehicles with internal combustion engines. It monitors the position and rotational speed of the crankshaft and sends the information to the engine control unit so it can make appropriate adjustments based on operating conditions. The crankshaft speed and position are some of the most important parameters used in engine management calculations, and many engines cannot run if the crankshaft position sensor is not providing an accurate signal.
Faulty crankshaft position sensor symptoms:
- Issues Starting the Vehicle
- Intermittent Stalling
- Check Engine Light Comes On
- Uneven Acceleration
- Engine Misfires or Vibrates
- Rough Idle and/or Vibrating Engine
- Reduced Gas Mileage
- FUSO TRUCK -> FN62F FIGHTER 2427 2016-
- FUSO TRUCK -> FN63F FIGHTER 2427 2016-
- HINO BUS -> RN8J 2007-2008/07
- HINO DUTRO -> XZU414 2003-2007
- HINO DUTRO -> XZU424 2003-2006/10
- HINO DUTRO -> XZU434 2003-2007
- HINO DUTRO -> XZU605 2019/09-
- HINO DUTRO -> XZU655 2019/09-
- HINO DUTRO -> XZU710 2019/09-
- HINO TRUCK -> FC2A 2019-
- HINO TRUCK -> FD2A 2019-
- HINO TRUCK -> FD7J, 1024, 1026, 1124, 1126 2011-2016
- HINO TRUCK -> FD8J, 1024, 1027 2008-2011
- HINO TRUCK -> FE2A 2019-
- HINO TRUCK -> FE7J, 1426 2011-
- HINO TRUCK -> FG8J, 1628 2011-2016
- HINO TRUCK -> FG8J, 1628 2017-
- HINO TRUCK -> FM1A, 2632, 2635 2017-
- HINO TRUCK -> FT8J, 1022 2008-2011
- HINO TRUCK -> FY1E, IMPORT 2006-
- HINO TRUCK -> GD8J, 1227 2008-2011
- HINO TRUCK -> GH1A, 1832, 1835 2016-2018
- HINO TRUCK -> GH1A, 1832, 1835 2019-
- HINO TRUCK -> GH8J, 1728 2011-2016
- HINO TRUCK -> GT8J, 1322 2008-2011
- HINO TRUCK -> GT8J, 1322 2011-
- ISUZU -> EXY52 2012-
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA150-HINO |
| Barcode # | 9314258113629 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | 9091905063 |
| Reference OEM Number | 89411-E0050 |
| Other OEM Numbers | 89411E0050, 89411-E0050, 89410.027, 90919-05005 |
| Related Part Numbers | 1V3904G, 89411.031, R61540090008, 029600-0570 |
| Trade Part Numbers | 9091905005, 0296000570, 3602120-621 |
| Product Specifics | |
| Sensor Type | CRANKSHAFT POSITION SENSOR |
| Type | Sensor |
| Features | Direct Fit |
| Manufacturer Warranty | 1 Year |
| Number of pins | 2 -pin connector |
| Connector Shape | oval |
| Supplementary Article Info | without cable |
| Housing Colour | Black |
| Number of mounting bores | 1 |
| Resistor | 2.1 kOhm |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.