Name: Camshaft Position Sensor Pair LH and RH to suit Nissan 350Z Z33 Skyline V35 VQ35
Brand: Aftermarket OEM Replacement
SKU: CSCA-350Z-CAM2
Price: 129.97 AUD
Availability: InStock

BRAND NEW *OEM Quality* pair of camshaft position sensors - both banks covered - to suit the Nissan VQ V6 range.

When one cam sensor goes the other is usually not far behind because both cook at the same rate - this pair does the whole job in one hit and ships from Cranbourne VIC.

TO SUIT

Suits the rear-drive and AWD VQ V6 platforms that run one cam sensor per bank - the 350Z Z33 coupe and roadster the Skyline V35 in CPV35 PV35 and NV35 form the Stagea PM35 PNM35 and NM35 Turbo the Elgrand ME51 MNE51 and NE51 the Murano Z50 and the Maxima J32.

FITMENT CHECK

This pair is one right hand exhaust side sensor and one left hand sensor - it is not two of the same part. The Maxima J31 PJ31 is NOT covered because it runs a different sensor arrangement. Navara D40 and Pathfinder R51 are not included in this pair.

OEM PART NUMBERS

23731-6J906 - right hand exhaust side
23731-6J90B - right hand exhaust side
23731-5M015 - right hand exhaust side
23731-AL61A - left hand side
23731-AL615 - left hand side
23731-AL616 - left hand side

OTHER PART NUMBERS

BOSCH: 0 986 JG1 628
VEMO: V38-72-0128
NTK-AU: EC0238
HELLA: 6PU 013 122-661
ASHIKA: 152-01-100
WALKER PRODUCTS: 235-1152

PACKAGE INCLUDES

2 x camshaft position sensors - 1 x right hand exhaust side with straight plug and 1 x left hand side angled plug. Both are direct plug-in to the factory loom.

ABOUT THIS SENSOR

The VQ V6 runs a camshaft position sensor on each cylinder head. Each one reports its own bank to the ECU so injection and ignition can be sequenced correctly. Lose either one and the ECU cannot phase that bank.

Both sensors sit in the same heat and both age at the same rate, which is why a car that has just had one replaced so often comes back a few months later with the other. Doing the pair together is the reason this listing exists.

COMMON SYMPTOMS OF FAILURE

Rough running or a dead miss on one bank
Check engine light with P0340 P0341 P0345 or P0365 stored
Crank with no start once a sensor fails outright
Hesitation and stumble under acceleration
Hard starting when the engine is hot
A second cam sensor code appearing soon after the first was fixed

[2008 - 2009] NISSAN 350Z Z33 COUPE 3.5 (3.5L V6 VQ35DE 206kW)
[2008 - 2008] NISSAN 350Z Z33 COUPE 3.5 (3.5L V6 VQ35DE 221kW)
[2002 - 2007] NISSAN 350Z Z33 COUPE 3.5 AAZ33 (3.5L V6 VQ35DE 206kW)
[2005 - 2007] NISSAN 350Z Z33 COUPE 3.5 AAZ33 (3.5L V6 VQ35DE 221kW)
[2008 - 2009] NISSAN 350Z Z33 ROADSTER 3.5 (3.5L V6 VQ35DE 206kW)
[2003 - 2007] NISSAN 350Z Z33 ROADSTER 3.5 AAZ33 (3.5L V6 VQ35DE 206kW)
[2005 - 2007] NISSAN 350Z Z33 ROADSTER 3.5 AAZ33 (3.5L V6 VQ35DE 221kW)
[2008 - 2009] NISSAN 350Z Z33 ROADSTER 3.5 BAZ33 (3.5L V6 VQ35HR 230kW)
[2006 - 2007] NISSAN SKYLINE V35 COUPE 2.5 (2.5L V6 VQ25DD 158kW)
[2003 - 2006] NISSAN SKYLINE V35 COUPE 3.5 CPV35 (3.5L V6 VQ35DE 206kW)
[2003 - 2007] NISSAN SKYLINE V35 COUPE 3.5 4X4 (3.5L V6 VQ35DE 206kW)
[2006 - 2007] NISSAN SKYLINE V35 SEDAN 2.5 4X4 NV35 (2.5L V6 VQ25DD 158kW)
[2003 - 2007] NISSAN SKYLINE V35 SEDAN 3.5 PV35 (3.5L V6 VQ35DE 200kW)
[2001 - 2003] NISSAN STAGEA M35 WAGON 2.5 TURBO AWD NM35 (2.5L V6 VQ25DET 206kW)
[2004 - 2007] NISSAN STAGEA M35 WAGON 3.5 PM35 (3.5L V6 VQ35DE 200kW)
[2004 - 2007] NISSAN STAGEA M35 WAGON 3.5 AWD PNM35 (3.5L V6 VQ35DE 200kW)
[2004 - 2010] NISSAN ELGRAND E51 MPV 2.5 ME51 (2.5L V6 VQ25DE 137kW)
[2004 - 2010] NISSAN ELGRAND E51 MPV 2.5 AWD MNE51 (2.5L V6 VQ25DE 137kW)
[2002 - 2010] NISSAN ELGRAND E51 MPV 3.5 AWD NE51 (3.5L V6 VQ35DE 177kW)
[2005 - 2009] NISSAN MURANO Z50 SUV 3.5 4X4 (3.5L V6 VQ35DE 172kW)
[2008 - 2013] NISSAN MAXIMA J32 SEDAN 3.5 (3.5L V6 VQ35DE 183kW)

How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKU	CSCA-350Z-CAM2
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CSCA-350Z-CAM2
Reference OEM Number	23731-6J906
Other OEM Numbers	23731-6J906, 23731-AL61A, 23731-6J90B, 23731-AL615
Related Part Numbers	SC268, SC269, EC0238, OSCA514, OSCA524
Trade Part Numbers	BOSCH: 0 986 JG1 628, VEMO: V38-72-0128, NTK-AU: EC0238
Product Specifics
Product Type	SENSOR
Sensor Type	CAMSHAFT POSITION SENSOR
Fitting Position	Left and Right Hand Side
Number of pins	3-Pin
Rated Voltage	12 V
Housing Colour	Black
Compatible Makes	Nissan
Fitment Type	Direct Replacement
Kit Quantity	2
Other Details
Note	2 sensors. 1 x RH 23731-6J906 + 1 x LH 23731-AL61A.