




Camshaft Position Sensor Renault Megane X84 1.6L K4M 2003-2008 8200459076
Direct fit replacement for Megane X84 1.6L K4M
BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT RENAULT
TO SUIT:
- Renault Kangoo F61 [2010-2012] 1.5L K9K Diesel
- Fiat 500 312 [2007-2009] 1.3L Multijet Diesel
OEM#
23731BN701, 8200033686, 8200285686
PACKAGE INCLUDES:
1 X OEM Quality CAMSHAFT POSITION SENSOR (3-PIN PLUG).
The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. The engine control unit knows when the first cylinder is at the top dead point through the combination of both sensor signals.
COMMON QUESTIONS
Do I need to program this sensor to my Fiat or Renault?
No programming is required. This is a direct plug-and-play hall effect sensor. However we recommend clearing any stored engine fault codes with an OBD2 scanner after installation.
- [2011-2013] RENAULT MASTER X62 DCi 145 2.3L M9T DIESEL VAN
- [2013-2021] RENAULT MASTER X62 DCi 150 2.3L M9T DIESEL VAN/BUS
- [2007-2014] RENAULT TRAFIC X83 2.0L M9R DIESEL VAN
- [2008-2016] RENAULT KOLEOS H45 DCi 2.0L M9R DIESEL
- [2008-2010] RENAULT MEGANE x84 SPORT 175 2.0L M9R DIESEL
- [2008-2011] RENAULT LAGUNA X91 DCi 2.0L M9R DIESEL
- [2011-2015] RENAULT LATITUDE X43 DCi 2.0L M9R DIESEL
- [2010-2019] RENAULT KANGOO F61 DCi 1.5L K9K DIESEL VAN
- [2003-2008] RENAULT MEGANE x84 1.6L K4M
- [2008-2010] RENAULT CLIO X85 SPORT 197 2.0L F4R
- [2007-2010] RENAULT GRAND SCENIC J84 2.0L F4R
- [2005-2009] RENAULT SCENIC J84 2.0L F4R
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | CSCA545-5 |
| Barcode # | 4047025204378 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | CAM-133 |
| Reference OEM Number | 23731-DB00A |
| Other OEM Numbers | 23731BN701, 8200033686, 8200285686 |
| Related Part Numbers | 0986280433, CSCA545, SC434 |
| Trade Part Numbers | 6PU 009 146-611, CHN3-A221, SS11005, V46-72-0036 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Type | Sensor |
| Features | Direct Fit |
| Manufacturer Warranty | 1 Year |
| Number of pins | 3 -pin connector |
| Connector Shape | oval |
| Supplementary Article Info | for camshaft, without cable, with seal ring |
| Fitting Depth | 28 mm |
| Rated Voltage | 12 V |
| Housing Colour | Black |
| Operating Mode | Electric |
| Number of mounting bores | 1 |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.