Suction Control Valve for Mazda 3 BK Mazda 6 GG GY 2.0L MZR-CD
Direct Fit Replaces RFY0-13-V21
BRAND NEW *OEM Quality* suction control valve to suit Mazda 3 BK and Mazda 6 GG GY 2.0L MZR-CD diesel.
Rough idle and stalling on the MZR-CD diesel often come down to this valve. It goes out with same-day dispatch before 12pm.
TO SUIT
Made for the Mazda 3 BK MZR-CD 2006 to 2009 and the Mazda 6 GG/GY 2.0L diesel 2006 to 2008 with the RF7J and RF8G common rail engines.
FITMENT CHECK
This is the short-body valve with a 2-pin plug. Compare it with your original before ordering - it matches numbers 294200-036#, 294200-016# and 294009-026#.
OEM PART NUMBERS
- RFY0-13-V21
- RFY0-13-V21A
- 1514885
OTHER PART NUMBERS
- DCRS300260
- V22-11-0010
- ESCV-NS-000
- 12.24228
PACKAGE INCLUDES
1 x suction control valve (SCV) with 2-pin connector.
ABOUT THIS SENSOR
The MZR-CD uses this valve to control fuel flow into the high-pressure pump. Correct metering keeps the diesel smooth at idle and responsive on the road.
When it wears the Mazda can stall when the clutch goes in or idle roughly once warm. The ECU may log a rail pressure fault and limit power.
COMMON SYMPTOMS OF FAILURE
- Stalling when the clutch is pressed
- Rough or unstable warm idle
- Hard starting
- Fault code P0087 or P0088
- Hesitation pulling away
- [07/06 - 04/09] MAZDA 3 BK12 MZR-CD (2.0L 4cyl RF8G/RF7J Euro 4 105kW)
- [07/06 - 04/09] MAZDA 3 BK14 MZR-CD (2.0L 4cyl RF8G/RF7J Euro 4 105kW)
- [10/06 - 02/08] MAZDA 6 GG14 DI (2.0L 4cyl RF7J Euro 4 105kW)
- [10/06 - 02/08] MAZDA 6 GY19 DI (2.0L 4cyl RF7J Euro 4 105kW)
What does a suction control valve (SCV) do?
The suction control valve (SCV) regulates the amount of fuel drawn into the high-pressure injection pump on common rail diesel engines. By controlling fuel intake at the pump inlet, the SCV allows the ECU to vary rail pressure from low idle pressure to maximum full-load pressure. This precise pressure control is essential for the accurate fuel metering that modern common rail diesel engines require for performance, fuel economy, and emissions compliance.
What are the symptoms of a failing suction control valve?
Common symptoms include rough or unstable idle, hard starting particularly from cold, the engine entering limp mode with reduced power, excessive black or white smoke from the exhaust, loss of power under load, and a Check Engine light with fuel rail pressure fault codes. SCVs can also fail intermittently due to contamination from degraded fuel, causing symptoms that appear and disappear without a consistent pattern.
Can a dirty suction control valve be cleaned?
Yes - if the SCV is sticking due to fuel contamination or varnish deposits rather than mechanical wear, cleaning with diesel injector cleaner or fuel system cleaner can sometimes restore operation. Remove the valve and spray cleaner through it while working the valve manually. However if the SCV solenoid has failed electrically or the valve body is mechanically worn, cleaning will not restore correct function and replacement is required.
Is there a difference between the suction control valve and the pressure control valve?
Yes - these are two different valves in the common rail fuel system. The suction control valve (SCV) is fitted to the inlet side of the high-pressure pump and controls how much fuel enters the pump. The pressure control valve (PCV) is fitted to the fuel rail or pump outlet and bleeds off excess pressure to maintain the correct rail pressure. Both affect fuel rail pressure but from opposite ends of the system. Fault codes will specify which valve is affected.
Will a faulty SCV cause the engine not to start?
A severely failed SCV can prevent the engine from starting if it causes rail pressure to be too low for injection to occur. More commonly a failing SCV causes hard starting with extended cranking before the engine fires. On cold mornings the symptoms are often worse as fuel viscosity is higher and rail pressure is harder to build. If the engine cranks normally but will not fire, checking fuel rail pressure with a scan tool will confirm if the SCV is the cause.
How long do suction control valves last?
SCVs are wear items that typically last the life of the vehicle under normal conditions with clean fuel. Premature failure is most commonly caused by contaminated fuel, extended oil service intervals (which affects fuel quality in the pump), or the use of poor-quality fuel. Vehicles used in dusty environments or operated with low fuel levels frequently are more susceptible to SCV wear. Replacing the SCV at the first sign of symptoms prevents more expensive injection pump damage.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SVSC100 |
| Reference OEM Number | RFY0-13-V21 |
| Other OEM Numbers | RFY0-13-V21, RFY0-13-V21A, 1514885 |
| Related Part Numbers | VSC100GEN VSC100 |
| Interchange Part Numbers | V22-11-0010, ESCV-NS-000, DCRS300260 |
| Product Specifics | |
| Product Type | SUCTION CONTROL VALVE |
| Fitting Position | Fuel Injection Pump |
| Number of pins | 2-Pin |
| Injection System | Common Rail |
| Valve Type | Control Valve |
| Compatible Makes | Mazda |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Short body valve - compare with your original before ordering |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.