




MAP Sensor 13628637900 for BMW B46 B58 B58TU S58 Engines F22 F23 F30 F32 G42
MAP Sensor for BMW B46 B58 B58TU S58 Engines
BRAND NEW OEM Quality MAP SENSOR (MANIFOLD ABSOLUTE PRESSURE SENSOR) FOR BMW F22, F23, F30, F32, G42, G87, G20, G80, G22, G82, G30, G01, G02, G05, G07, and G29 TURBOCHARGED models.
OEM# 13 62 8 637 900, 13628637900
PACKAGE INCLUDES:
1 X OEM Quality MANIFOLD ABSOLUTE PRESSURE SENSOR (4-PIN PLUG). 2.5 BAR PRESSURE SENSOR
The boost pressure sensor is a crucial component in a turbocharged or supercharged engine system. It measures the pressure of the air entering the engine to ensure the proper functioning of the forced induction system. This sensor helps the engine control unit (ECU) optimize the air-fuel mixture for better performance and fuel efficiency, and to prevent any potential damage to the engine due to over-boosting.
If there are issues with this sensor, it can lead to poor engine performance, reduced power, or even trigger the engine warning light. Replacing or troubleshooting this sensor might be necessary if there are noticeable problems with the vehicle's performance.
2 Series
- F22 / F23 (2014-2021) > 230i
- F22 / F23 (2014-2021) > 230i xDrive
- F22 / F23 (2014-2021) > M240i
- F22 / F23 (2014-2021) > M240i xDrive
2 Series
- G42 / G43 (2022+) > 230i
- G42 / G43 (2022+) > 230i xDrive
- G42 / G43 (2022+) > M240i
- G42 / G43 (2022+) > M240i xDrive
2 Series
- G87 (2024-) > M2 (2024+)
3 Series
- F30 / F31 / F34 (2012-2019) > 330i
- F30 / F31 / F34 (2012-2019) > 330i xDrive
- F30 / F31 / F34 (2012-2019) > 340i
- F30 / F31 / F34 (2012-2019) > 340i xDrive
3 Series
- G20 (2019+) > 330i
- G20 (2019+) > 330i xDrive
- G20 (2019+) > M340i
- G20 (2019+) > M340i xDrive
3 Series
- G80 (2021-) > M3 (2021-)
- G80 (2021-) > M3 Competition RWD (2021-)
- G80 (2021-) > M3 xDrive Competition (2021-)
4 Series
- F32 / F33 / F36 (14-20) > 430i
- F32 / F33 / F36 (14-20) > 430i xDrive
- F32 / F33 / F36 (14-20) > 440i
- F32 / F33 / F36 (14-20) > 440i xDrive
4 Series
- G22 / G23 (2021+) > 430i
- G22 / G23 (2021+) > 430i xDrive
- G22 / G23 (2021+) > M440i
- G22 / G23 (2021+) > M440i xDrive
4 Series
- G26 (2022+) > 430i Gran Coupe
- G26 (2022+) > 430i xDrive Gran Coupe
- G26 (2022+) > M440i xDrive Gran Coupe
4 Series
- G82 / G83 (2021-) > M4 (2021-)
- G82 / G83 (2021-) > M4 CSL
- G82 / G83 (2021-) > M4 Competition RWD (2021-)
- G82 / G83 (2021-) > M4 GT4 (2022+)
- G82 / G83 (2021-) > M4 xDrive Competition (2021-)
5 Series
- G30 (2017-2023) > 530i
- G30 (2017-2023) > 530i xDrive
- G30 (2017-2023) > 540i (B58A 2017-2019)
- G30 (2017-2023) > 540i (B58C 2020-2023)
- G30 (2017-2023) > 540i xDrive (B58A 2017-2019)
- G30 (2017-2023) > 540i xDrive (B58C 2020-2023)
7 Series
- G12 (2016-2023) > 740i
- G12 (2016-2023) > 740i xDrive
8 Series
- G14 / G15 / G16 (2019+) > 840i xDrive
X1 Series
- F48 X1 (2016-2023) > X1 28i
- F48 X1 (2016-2023) > X1 28i xDrive
X2 Series
- F39 X2 (2018-2023) > X2 M35i (18-23)
- F39 X2 (2018-2023) > X2 sDrive28i FWD (18-23)
- F39 X2 (2018-2023) > X2 xDrive28i (18-23)
X3 Series
- F97 X3M (2020+) > X3M
X3 Series
- G01 X3 (2018+) > X3 M40i B58A (2018-2019)
- G01 X3 (2018+) > X3 M40i B58D (2020+)
- G01 X3 (2018+) > X3 xDrive30i
X4 Series
- F98 X4M (2020+) > X4M
X4 Series
- G02 X4 (2019+) > X4 M40i
- G02 X4 (2019+) > X4 xDrive30i
X5 Series
- G05 X5 (2019+) > X5 xDrive40i B58C (2019-2023)
X6 Series
- G06 X6 (2020+) > X6 sDrive 40i B58C (2019-2023)
- G06 X6 (2020+) > X6 xDrive 40i B58C (2019-2023)
X7 Series
- G07 X7 (2019+) > X7 xDrive40i B58C (2019-2022)
Z Series
- G29 Z4 (2019+) > Z4 M40i
- G29 Z4 (2019+) > Z4 sDrive30i
What fault codes does a faulty MAP sensor trigger?
A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.
How do I test a MAP sensor?
With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.
Can I drive with a faulty MAP sensor?
You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.
What does a MAP sensor do?
The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.
What are the symptoms of a faulty MAP sensor?
Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.
What is the difference between a MAP sensor and a MAF sensor?
A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.
| Identification | |
|---|---|
| SKU | MS-E132 |
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | MS-E132 |
| Reference OEM Number | 13628637900 |
| Other OEM Numbers | 13 62 8 637 900, 13628637900 |
| Related Part Numbers | V20-72-0046 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Manifold Absolute Pressure (MAP) Sensor |
| Number of pins | 4 -pin connector |
| Connector Shape | oval |
| Supplementary Article Info | with integrated air temperature sensor |
| Pressure Range | 2 kPa to 262 kPa |
| Number of mounting bores | 1 |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.