MAP Sensor for Chrysler 300C Jeep Commander Grand Cherokee WH 5.7L Hemi V8
Direct Fit Replaces 5033310AC
BRAND NEW *OEM Quality* MAP sensor to suit the Chrysler 300C, Jeep Commander XH and Jeep Grand Cherokee WH WK with the 5.7L Hemi V8.
The Hemi 300C and the Commander are big, thirsty engines, and a tired MAP sensor makes them feel flat and cost more at the bowser. This plug-in replacement is packed and shipped from Melbourne.
TO SUIT
- Chrysler 300C sedan 5.7L Hemi EZB EZD EZH V8 (250kW), 01/2005 to 12/2011
- Chrysler 300C wagon 5.7L Hemi V8 (250kW), 01/2006 to 12/2009
- Jeep Commander XH 5.7L Hemi EZB V8, 11/2006 to 12/2010
- Jeep Grand Cherokee WH WK 5.7L Hemi V8, 01/2005 to 12/2008
FITMENT CHECK
These applications use a 3-pin plug. Please confirm against your existing sensor and the OEM part numbers below before ordering.
OEM PART NUMBERS
- 5033310AC
- 5149091AA
- 56028562AB
- 56041018AC
- 56041018AD
- 68199324AA
- 68199324AB
- K68199324AB
- 6102192AA
OTHER PART NUMBERS
- ECM-CH-005
- MA0182
- TMP043
- MAP1209
PACKAGE INCLUDES
1 x MAP sensor with 3-pin oval connector.
ABOUT THIS SENSOR
The first generation Hemi V8 relies on the MAP sensor to measure manifold pressure and trim fuelling for the road, towing and cruising. After many years of heat cycles original sensors often drift.
A faulty sensor can bring a hunting idle, hesitation and codes such as P0106 or P0107. A new sensor restores a clean signal.
COMMON SYMPTOMS OF FAILURE
- Check engine light with P0106 or P0107
- Hunting idle
- Hesitation off the line
- Increased fuel use
- Black smoke from the exhaust
- [01/07 - 12/11] CHRYSLER 300C 3.5L V6 EGG 183kW
- [01/07 - 12/09] CHRYSLER 300C 3.5L V6 EGG 183kW
- [01/05 - 12/11] CHRYSLER 300C 5.7L V8 Hemi EZB, EZD, EZH 250kW
- [01/06 - 12/09] CHRYSLER 300C 5.7L V8 Hemi EZB, EZD, EZH 250kW
- [01/08 - 12/11] CHRYSLER GRAND VOYAGER Gen5 RT 3.8L V6 EGL 142kW
- [01/07 - 12/11] CHRYSLER SEBRING JS 2.7L V6 EER
- [01/07 - 12/09] CHRYSLER SEBRING JS 2.7L V6 EER
- [01/08 - 12/10] DODGE AVENGER JS 2.7L V6 EER 137kW
- [01/08 - 12/11] DODGE JOURNEY JC 2.0L 4cyl ECE 103kW
- [01/08 - 12/11] DODGE JOURNEY JC 2.7L V6 EER 136kW
- [01/14 - 12/21] JEEP CHEROKEE KL 2.4L 4cyl MULTIAIR ED6 130kW
- [11/06 - 12/10] JEEP COMMANDER XH 5.7L V8 Hemi EZB
- [01/99 - 12/05] JEEP GRAND CHEROKEE GEN2 WG-WJ 4.0L 6cyl ERH
- [01/05 - 12/08] JEEP GRAND CHEROKEE GEN3 WH-WK 5.7L V8 Hemi EZB, EZD, EZH
- [01/10 - 12/11] JEEP GRAND CHEROKEE GEN4 WK2 5.7L V8 Hemi EZD 259kW
- [01/11 - 12/13] JEEP GRAND CHEROKEE GEN4 WK2 5.7L V8 Hemi EZH 259kW
- [01/13 ON] JEEP GRAND CHEROKEE GEN4 WK2 5.7L V8 Hemi EZH 259kW
- [02/11 - 12/11] JEEP WRANGLER JK 3.8L V6 EGH, EGT 146kW
- [06/08 - 09/09] JEEP WRANGLER JK 3.8L V6 EGH, EGT 146kW
- [06/08 - 12/11] JEEP WRANGLER JK 3.8L V6 EGH, EGT 146kW
What fault codes does a faulty MAP sensor trigger?
A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.
How do I test a MAP sensor?
With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.
Can I drive with a faulty MAP sensor?
You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.
What does a MAP sensor do?
The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.
What are the symptoms of a faulty MAP sensor?
Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.
What is the difference between a MAP sensor and a MAF sensor?
A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.
| Identification | |
|---|---|
| Brand | Aftermarket OEM Replacement |
| Part Numbers | |
| Part Number | SMP183 |
| Reference OEM Number | 5033310AC |
| Other OEM Numbers | 5149091AA, 56028562AB, 56041018AC, 56041018AD, 68199324AB |
| Related Part Numbers | ECM-CH-005, MP183, TMP043, MA0182, MAP1209 |
| Interchange Part Numbers | ECM-CH-005, MA0182, TMP043, MAP1209 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | Manifold Absolute Pressure (MAP) Sensor |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Mounting Type | Pressed |
| Pressure Range | 5 kPa, until 120 kPa |
| Compatible Makes | Chrysler, Jeep |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Confirm 3-pin plug and mount against your sensor before ordering |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.