MAF Mass Air Flow Sensor for BMW 320i 328i 420i 428i 520i F30 F31 F32 F10 N20 MAF Mass Air Flow Sensor for BMW 320i 328i 420i 428i 520i F30 F31 F32 F10 N20 MAF Mass Air Flow Sensor for BMW 320i 328i 420i 428i 520i F30 F31 F32 F10 N20 MAF Mass Air Flow Sensor for BMW 320i 328i 420i 428i 520i F30 F31 F32 F10 N20

MAF Mass Air Flow Sensor for BMW 320i 328i 420i 428i 520i F30 F31 F32 F10 N20

Part #: SCAF189 Replaces OEM: 13627602038

OEM Spec Fit Replaces 13627602038

$148.97
RRP $300.00
SAVE $151.03 (50%)
In Stock

BRAND NEW *OEM Quality* mass air flow sensor to suit BMW 3 and 4 Series 320i 328i 420i 428i with the N20 2.0L turbo engine.

If your BMW has lost its punch under boost or keeps throwing a drivetrain warning with a lean code this meter is the usual fix. Same-day dispatch before 12pm from our Melbourne warehouse.

TO SUIT

Made for the F30 320i and 328i sedan built from 2012 to 2018 with the N20 B20 four-cylinder turbo engine (135kW and 180kW). It also fits the F31 Touring F34 Gran Turismo and the F32 F33 F36 420i and 428i coupe convertible and Gran Coupe.

The same N20 meter is used on the F10 520i and 528i plus the Z4 E89 sDrive20i and 28i. See the full compatibility list for every variant and date range.

FITMENT CHECK

Some variants changed meter part way through production - the 316i to 07/2015 and the 420i 428i coupe to 02/2016. Check the build date notes in the compatibility list and match your old meter to OEM 13627602038 or 7602038.

OEM PART NUMBERS

  • BMW: 13627602038
  • BMW: 7602038
  • MINI: 13627602038

OTHER PART NUMBERS

  • 0280218266
  • V20-72-5174
  • 8ET358095461
  • EPP-BM-018
  • 245-1292
  • 2505120
  • 7.07759.65.0
  • AM8266GEN
  • AMM9416

PACKAGE INCLUDES

1 x mass air flow meter insert with 4-pin oval connector. Insert only - fits into your existing intake duct housing. No air temperature sensor built in.

ABOUT THIS SENSOR

The hot film meter measures the mass of air entering the N20 turbo engine so the DME can set fuel and boost. On the 320i and 328i a contaminated or drifting element usually reads low - the engine runs lean and the DME pulls power to protect itself.

Oiled aftermarket air filters and a split intake boot after the meter are common causes on high-kilometre F30s - check both when fitting the new meter.

COMMON SYMPTOMS OF FAILURE

  • Drivetrain malfunction or reduced power message
  • Hesitation or flat spot under boost
  • Rough or hunting idle after a cold start
  • Fault codes P0101 P0102 or P0103
  • Lean codes P0171 with higher fuel consumption
  • [07/12 - 08/16] BMW 3 F30 / F80 316 i (1.6L 4cyl N13 B16 A 100kW) - built to 07/15
  • [07/15 - 10/18] BMW 3 F30 / F80 318 i (1.5L 3cyl B38 B15 A 100kW)
  • [03/12 - 10/18] BMW 3 F30 / F80 320 i (2.0L 4cyl N20 B20 D / N20 B20 B / N20 B20 A 135kW)
  • [11/11 - 10/18] BMW 3 F30 / F80 328 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW) - built from 02/12 built to 08/15
  • [02/14 - 10/18] BMW 3 F30 / F80 328 i ActiveFlex (2.0L 4cyl N20 B20 A 180kW)
  • [11/12 - 06/15] BMW 3 F31 320 i (2.0L 4cyl N20 B20 B 135kW)
  • [07/12 - 06/15] BMW 3 F31 328 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW)
  • [03/13 - 06/16] BMW 3 F34 320 i (2.0L 4cyl N20 B20 B / N20 B20 A 135kW) - built from 06/13
  • [03/13 - 06/16] BMW 3 F34 328 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW)
  • [11/13 - 02/17] BMW 4 F32 / F82 420 i (2.0L 4cyl N20 B20 B / N20 B20 A 135kW) - built to 02/16
  • [07/13 - 02/17] BMW 4 F32 / F82 428 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW) - built to 02/16
  • [07/14 - 02/16] BMW 4 F33 / F83 420 i (2.0L 4cyl N20 B20 B 135kW)
  • [11/13 - 02/17] BMW 4 F33 / F83 428 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW) - built to 02/16
  • [03/14 - 02/17] BMW 4 F36 420 i (2.0L 4cyl N20 B20 B 135kW) - built to 12/16
  • [03/14 - 06/16] BMW 4 F36 428 i (2.0L 4cyl N26 B20 A / N20 B20 A 180kW)
  • [09/11 - 07/15] BMW 5 F10 520 i (2.0L 4cyl N20 B20 B / N20 B20 A 135kW)
  • [09/11 - 07/15] BMW 5 F10 528 i (2.0L 4cyl N20 B20 A 180kW)
  • [03/14 - 02/18] BMW i8 I12 hybrid (1.5L 3cyl B38 K15 A 266kW) - built from 06/14
  • [03/18 - 06/20] BMW i8 I12 hybrid (1.5L 3cyl B38 K15 A 275kW)
  • [03/18 - 06/20] BMW i8 I15 hybrid (1.5L 3cyl B38 K15 A 275kW)
  • [09/11 - 08/16] BMW Z4 E89 sDrive 20 i (2.0L 4cyl N20 B20 A 135kW)
  • [09/11 - 08/16] BMW Z4 E89 sDrive 28 i (2.0L 4cyl N20 B20 A 180kW)
Can I clean my MAF sensor instead of replacing it?

Yes - if the sensor is contaminated rather than electrically failed, cleaning with a dedicated MAF sensor cleaner spray can restore correct readings. Do not use brake cleaner or generic electrical contact cleaner as these leave residue that damages the sensing wire. Allow the sensor to dry completely before reinstalling. If cleaning does not resolve the fault codes, the sensor requires replacement.

What is the difference between a MAF sensor and a MAP sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine using a hot wire element in the intake. A MAP (Manifold Absolute Pressure) sensor measures intake manifold pressure to calculate air density. Most modern engines use one or the other - some use both. Your vehicle service manual or OBD2 fault codes will confirm which sensor type your engine uses.

Will a faulty MAF sensor cause my vehicle to fail an emissions test?

Yes. A faulty MAF sensor causes the ECU to miscalculate fuel delivery, typically resulting in a rich running condition that increases CO and hydrocarbon emissions. Most roadworthy and emissions checks will fail a vehicle with an active MAF sensor fault code or visibly excessive exhaust smoke.

What are the symptoms of a bad MAF sensor?

Common symptoms include rough idle, hesitation or stumbling on acceleration, poor fuel economy, black smoke from the exhaust, and an illuminated Check Engine light. Your ECU may log fault codes P0100 to P0104.

Can I drive with a faulty MAF sensor?

You can drive short distances but it is not recommended. A faulty MAF sensor causes the ECU to run incorrect fuel mixtures, which can damage the catalytic converter and O2 sensors over time. Have it replaced as soon as possible.

How do I test if my MAF sensor is bad?

Use an OBD2 scanner to check for fault codes P0100-P0104. You can also use a multimeter or live data scanner to check the sensor output voltage against your vehicle's specification. A reading significantly outside spec confirms a faulty sensor.

What causes a MAF sensor to fail?

The most common causes are a dirty or contaminated sensing element (often from a missing or damaged air filter), oil contamination from an over-oiled aftermarket air filter, heat damage, or general wear over time.

Do I need to reset my ECU after replacing the MAF sensor?

It is good practice to clear any stored fault codes using an OBD2 scanner after replacement. Some vehicles will self-adapt within a short drive cycle, but clearing codes ensures the ECU recalibrates from a clean baseline.

Identification
BrandAftermarket OEM Replacement
Part Numbers
Part NumberSCAF189
Reference OEM Number13627602038
Other OEM Numbers13627602038, 7602038
Related Part NumbersAM8266GEN, 0280218266, AMM9416, CAF189
Interchange Part Numbers0280218266, V20-72-5174, 8ET358095461, EPP-BM-018, 245-1292
Product Specifics
Product TypeSENSOR
Sensor TypeMass Air Flow (MAF) Sensor
Number of pins4-Pin
Connector Shapeoval
Voltage12 V
Housing Typewithout housing
Mounting TypeBolted
Compatible MakesBMW
Fitment TypeDirect Replacement
Other Details
NoteInsert only - no housing. Check build date notes in fitment

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category