Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98 Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98

Pre-Cat O2 Sensor 12569429 Holden Commodore VZ VE VF V8 LS2 L76 L77 L98

Part #: COS1036 OEM #: 12569429 SKU: COS1036-1

Direct Fit Replaces 12569429

$78.39
RRP $168.99
SAVE $90.60 (54%)
In Stock

BRAND NEW *OEM Quality* OXYGEN SENSOR (LAMBDA SENSOR) TO SUIT HOLDEN 6.0L V8 GEN4 (L76 / L77 / L98) ENGINES

 

TO SUIT:

HOLDEN 6.0L V8 GEN4 (LS2 / L76 / L77 / L98) ENGINES

  • [2006-2013] COMMODORE VE V8
  • [2013-2017] COMMODORE VF V8
  • [2006-2013] STATESMAN / CAPRICE WM
  • [2013-2017] CAPRICE WN 6.0L
  • [2006-2010] STATESMAN WM 6.0L L76

HOLDEN 5.7L V8 GEN3 LS1 ENGINES (also suits)

  • [2002-2006] COMMODORE VY / VZ
  • [2003-2006] STATESMAN / CAPRICE WK / WL
  • [2003-2006] MONARO V2 / VZ
  • [2003-2007] ADVENTRA VY / VZ
  • [2003-2006] CREWMAN VY / VZ

 

OEM#

12569429 12573167 12576131 12580827 12583290 12583804 12584925 12587785 12590790 12594452 12596701 12597878 12606569 12607410 12609001 12611127

 

ABOUT THIS PART:

This pre-cat oxygen sensor monitors exhaust oxygen levels upstream of the catalytic converter and reports to the ECU to maintain the correct air-fuel ratio. A faulty upstream O2 sensor causes the engine to run rich or lean reducing fuel economy and triggering the check engine light. Direct OEM fit with pre-greased thread — no modifications required.

 

SYMPTOMS OF A FAILING SENSOR:

  • Check Engine Light (fault codes P0130–P0135 or P0150–P0155)
  • Increased fuel consumption
  • Rough idle or poor throttle response
  • Failed emissions test

 

PACKAGE INCLUDES:

1 x *OEM Quality* Oxygen Sensor (4-pin square connector)

4-wire heated | Pre-Cat (upstream) | 375mm total length

Note: 2 sensors required per vehicle

 

An oxygen sensor (lambda sensor) sits in the exhaust stream and measures oxygen content in the exhaust gases. It compares this to ambient air oxygen levels and sends feedback to the Engine Control Module (ECM) to adjust the air-fuel mixture for optimal combustion efficiency.

  • HOLDEN ADVENTRA
  • VY AWD 5.7L V8 LS1 (2003-2004)
  • VZ AWD 5.7L V8 LS1 (2004-2007)
  •  
  • HOLDEN CALAIS
  • VY 5.7L V8 LS1 (2003-2004)
  • VZ 5.7L V8 LS1 (2004-2006)
  • VE 6.0L V8 L98/L77 (2006-2013)
  • VF 6.0L V8 L77 (2013-2017)
  •  
  • HOLDEN CAPRICE
  • WK 5.7L V8 LS1 (2003-2004)
  • WL 5.7L V8 LS1 (2004-2006)
  • WM 6.0L V8 L76/L77 (2006-2013)
  • WN 6.0L V8 L77 (2013-2017)
  •  
  • HOLDEN COMMODORE
  • VY 5.7L V8 LS1 (2002-2004)
  • VZ 5.7L V8 LS1 (2004-2007)
  • VE 6.0L V8 L76/L77 (2006-2013)
  • VF 6.0L V8 L77 (2013-2017)
  •  
  • HOLDEN CREWMAN
  • VY 5.7L V8 LS1 (2003-2004)
  • VZ 5.7L V8 LS1 (2004-2007)
  •  
  • HOLDEN MONARO
  • V2 5.7L V8 LS1 (2003-2004)
  • VZ 5.7L V8 LS1 (2004-2006)
  •  
  • HOLDEN ONE TONNER
  • VY 5.7L V8 LS1 (2003-2004)
  • VZ 5.7L V8 LS1 (2004-2005)
  •  
  • HOLDEN STATESMAN
  • WK 5.7L V8 LS1 (2003-2004)
  • WL 5.7L V8 LS1 (2004-2006)
  • WM 6.0L V8 L76 (2006-2010)
How do I replace an oxygen sensor?

Most O2 sensors thread directly into the exhaust pipe or manifold. You will need an O2 sensor socket (22mm with a slot for the wire) and penetrating oil if the sensor is seized. Allow the exhaust to cool completely before starting. Some sensors also require a wiring harness connector to be unplugged. Always clear fault codes with an OBD2 scanner after replacement.

What fault codes does a faulty O2 sensor trigger?

A faulty O2 sensor typically triggers codes P0130 to P0167. The specific code indicates which sensor has failed - P0130 to P0138 relate to Bank 1 sensors and P0150 to P0158 relate to Bank 2 sensors. An OBD2 scanner will identify the exact sensor location.

Can I use a universal O2 sensor on my vehicle?

Universal sensors can work but require splicing the wiring harness which introduces risk of connection faults. A direct-fit aftermarket OEM replacement sensor with the correct connector plugs directly in with no cutting or splicing required. SensorGal stocks direct-fit sensors cross-referenced to OEM part numbers for most Australian vehicles.

How do I know if my O2 sensor is bad?

Common signs include poor fuel economy, rough idle, failed emissions test, rotten egg smell from the exhaust, and a Check Engine light with codes P0130-P0167. An OBD2 scanner showing a flat or sluggish O2 sensor waveform on live data also indicates a faulty sensor.

What is the difference between upstream and downstream O2 sensors?

The upstream (pre-cat) sensor monitors exhaust gases to help the ECU calculate fuel trim. The downstream (post-cat) sensor monitors catalytic converter efficiency. They serve different functions and are not interchangeable even if they look identical.

Can a bad O2 sensor damage my catalytic converter?

Yes. A faulty upstream O2 sensor can cause the engine to run rich, sending unburnt fuel into the catalytic converter. Over time this overheats and destroys the catalyst. Replacing the O2 sensor promptly protects your catalytic converter.

How many O2 sensors does my vehicle have?

Most 4-cylinder vehicles have two O2 sensors (one upstream, one downstream). V6 and V8 engines typically have four - one upstream and one downstream per bank. Contact us with your vehicle details and we will confirm the correct quantity and part numbers.

Identification
SKUCOS1036-1
Barcode #28851152846
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCOS1036
Reference OEM Number12569429
Other OEM Numbers12569429, 12573167, 12607410, 12583804
Related Part NumbersEGO-106, OX427, ES20013, 0258986507, F00HL00111
Trade Part NumbersDenso: 234-4668, ACDelco: 213-1687
Product Specifics
Sensor TypeOxygen Sensor
Placement On VehiclePRE-CAT
TypeSensor
FeaturesDirect Fit
Ean028851152846
Number Of Sensors1
Fitting PositionPre-cat
Number of pins4-pin connector
Connector ShapeSquare
Total Length375 mm
Other Details
Note4-pin square connector - 375mm total length - finger probe
Unit Of Measureea

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

Others Also Bought

More From This Category