Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13 Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13

Oxygen Sensor for Holden Statesman Caprice WL Wm 3.6L V6 Leo LY7 LW2 04-13

Part #: COS1195 OEM #: 92210450 SKU: COS1195_0258986727-6

Direct fit replacement for WL WM Statesman Caprice

$79.97
RRP $116.99
SAVE $37.02 (32%)
In Stock

BRAND NEW Post-Cat Narrowband Oxygen Sensor (Lambda Sensor)

4-wire narrowband oxygen sensor for Holden Caprice and Statesman WL/WM series with 3.6L V6 engine.

NOT COMPATIBLE WITH LFX/LFW SIDI DIRECT INJECTION ENGINES. Verify your engine code before ordering.

SPECIFICATIONS

  • Type: 4-Wire Narrowband Oxygen Sensor
  • Connector: 4-pin oval connector
  • Cable Length: 400mm
  • Thread: M18x1.5
  • Placement: Post-Catalytic Converter

TO SUIT

  • [08/04 - 07/06] HOLDEN CAPRICE WL Sedan 3.6L V6 LY7 190kW
  • [07/06 - 08/13] HOLDEN CAPRICE WM Sedan 3.6L V6 LY7/LLT/LFX
  • [08/04 - 07/06] HOLDEN STATESMAN WL Sedan 3.6L V6 LY7 190kW
  • [07/06 - 08/13] HOLDEN STATESMAN WM Sedan 3.6L V6 LY7/LLT

PART NUMBER: COS1195

OEM CROSS REFERENCE

  • GM / Holden: 92210450, 55566592, 24403182
  • Bosch: 0258986727, 0258006378
  • NTK: OZA770-EE4
  • DENSO: DOX-2050
  • [08/04 - 07/06] HOLDEN CAPRICE WL Sedan 3.6L V6 LY7 190kW
  • [07/06 - 08/13] HOLDEN CAPRICE WM Sedan 3.6L V6 LY7/LLT/LFX
  •  
  • [08/04 - 07/06] HOLDEN STATESMAN WL Sedan 3.6L V6 LY7 190kW
  • [07/06 - 08/13] HOLDEN STATESMAN WM Sedan 3.6L V6 LY7/LLT
How do I replace an oxygen sensor?

Most O2 sensors thread directly into the exhaust pipe or manifold. You will need an O2 sensor socket (22mm with a slot for the wire) and penetrating oil if the sensor is seized. Allow the exhaust to cool completely before starting. Some sensors also require a wiring harness connector to be unplugged. Always clear fault codes with an OBD2 scanner after replacement.

What fault codes does a faulty O2 sensor trigger?

A faulty O2 sensor typically triggers codes P0130 to P0167. The specific code indicates which sensor has failed - P0130 to P0138 relate to Bank 1 sensors and P0150 to P0158 relate to Bank 2 sensors. An OBD2 scanner will identify the exact sensor location.

Can I use a universal O2 sensor on my vehicle?

Universal sensors can work but require splicing the wiring harness which introduces risk of connection faults. A direct-fit aftermarket OEM replacement sensor with the correct connector plugs directly in with no cutting or splicing required. SensorGal stocks direct-fit sensors cross-referenced to OEM part numbers for most Australian vehicles.

How do I know if my O2 sensor is bad?

Common signs include poor fuel economy, rough idle, failed emissions test, rotten egg smell from the exhaust, and a Check Engine light with codes P0130-P0167. An OBD2 scanner showing a flat or sluggish O2 sensor waveform on live data also indicates a faulty sensor.

What is the difference between upstream and downstream O2 sensors?

The upstream (pre-cat) sensor monitors exhaust gases to help the ECU calculate fuel trim. The downstream (post-cat) sensor monitors catalytic converter efficiency. They serve different functions and are not interchangeable even if they look identical.

Can a bad O2 sensor damage my catalytic converter?

Yes. A faulty upstream O2 sensor can cause the engine to run rich, sending unburnt fuel into the catalytic converter. Over time this overheats and destroys the catalyst. Replacing the O2 sensor promptly protects your catalytic converter.

How many O2 sensors does my vehicle have?

Most 4-cylinder vehicles have two O2 sensors (one upstream, one downstream). V6 and V8 engines typically have four - one upstream and one downstream per bank. Contact us with your vehicle details and we will confirm the correct quantity and part numbers.

Identification
SKUCOS1195_0258986727-6
Barcode #4047025020411
BrandAftermarket OEM Replacement
Part Numbers
Part NumberCOS1195
Reference OEM Number92210450
Other OEM Numbers55566592, 92171135, 92210450, 9195606, 24403182
Related Part Numbers0258986727, COS1195, EGO-135, OX425
Trade Part NumbersBOSCH: 0258986727, NTK: OZA770-EE4
Product Specifics
TypeOxygen / Lambda Sensor
Thread SizeM18x1.5
Number of pins4-Pin
Connector Shapeoval
Cable Length400mm
Fitment TypeDirect Replacement
BrandAftermarket Replacement
PlacementPost-Catalytic Converter
Number of Wires4-Wire
Other Details
Note4-pin oval connector - 4-wire - 400mm cable - M18x1.5

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

Others Also Bought

More From This Category