Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768 Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768

Camshaft Sensor for Mitsubishi Triton MQ MR 2.4L 4G64 2014 -ON MR578768

Part #: MR578768 OEM #: MR578768 SKU: V37720100

Camshaft Sensor 4G64 Engine Mitsubishi Triton MQ MR

$139.97
RRP $194.99
SAVE $55.02 (28%)
In Stock

BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT MITSUBISHI

 

Package Includes:

1* CAMSHAFT POSITION SENSOR (3-PIN PLUG).

 

OEM# MR478768, MR578768

 

  • MITSUBISHI ASX (GA_W_, XA, XB, XC, XD) 1.8 DI-D 4WD (GA6W) 06.2010- 110kw SUV
  • MITSUBISHI ASX (GA_W_, XA, XB, XC, XD) 2.2 DI-D 4WD (GA8W) 04.2013- 110kw SUV
  •  
  • MITSUBISHI COLT VI (Z3_A, Z2_A, RG) 1.5 (Z27) 09.2004-02.2006 72kw Hatchback
  • MITSUBISHI COLT VI (Z3_A, Z2_A, RG) 1.5 Ralliart (Z23) 09.2006-06.2012 113kw Hatchback
  • MITSUBISHI COLT VI Convertible (RG) 1.5 Turbo (Z37A) 05.2006-07.2009 110kw Convertible
  •  
  • MITSUBISHI DELICA D5 (CV_W) 2.2 DI-D 4WD (CV1W) 03.2013- 109kw MPV
  • MITSUBISHI GRANDIS (NA_W, BA) 2.4 MIVEC (NA4W) 04.2004-12.2011 121kw MPV
  • MITSUBISHI OUTLANDER III Wagon (GG_W, GF_W, ZJ, ZL, ZK) 2.2 DI-D 4WD (GF6W) 08.2012- 110kw SUV
  •  
  • MITSUBISHI TRITON Pickup (KA_T, ML, MN, KB_T) 3.5 (KA9T) 07.2006-12.2011 135kw Pickup
  • MITSUBISHI TRITON Pickup (KA_T, ML, MN, KB_T) 3.5 4WD (KB9T) 07.2006-12.2010 135kw Pickup
  • MITSUBISHI TRITON Pickup (KJ_, MQ, KK_, KL_, MR) 2.4 (KK4T) 11.2014- 94kw Pickup
  • MITSUBISHI TRITON Platform/Chassis (MN, ML, KA_T, KB_T) 3.5 i 4WD (KB9T) 07.2006-12.2009 135kw Platform/Chassis
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKUV37720100
Barcode #5050063244786
BrandAftermarket OEM Replacement
Part Numbers
Part NumberMR578768
Reference OEM NumberMR578768
Other OEM NumbersMR578768
Related Part NumbersADC47221
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Number of pins3 -pin connector
Connector Shapeoval
Supplementary Article Infowithout cable
Fitting Depth26.7 mm
Voltage12 V
Housing ColourBlack
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category