BRAND NEW *OEM Quality* MAP sensor (manifold absolute pressure / air temperature) to suit Ford Falcon XR8 / GT / GTP / FPV / Fairlane 5.4L V8 Boss and Barra V8.

If your V8 Falcon is hesitating, flat-spotting under load, or showing a P0106-P0109 fault code, a failing MAP sensor disrupts the fuel calculations the Boss and Barra V8 depends on for performance. This direct replacement covers the full range of 5.4L V8 applications - dispatched same-day before 12pm from Cranbourne VIC.

TO SUIT

Designed for Ford Falcon 5.4L V8 models including XR8 BA/BF/FG (Boss 260/290/315), GT/GTP/GT-P/GT Cobra BA/BF/FG, FPV GS/Force 8 BF/FG, Fairlane BA/BF 5.4L, Fairmont BA/BF 5.4L V8, LTD BA/BF 5.4L V8, and the Falcon AU Series 2/3 5.0L V8 Windsor. Also fits the Ford F-150 5.4L V8 AWD (2004-2007).

FITMENT CHECK

Fits AU Series 2 and 3 V8 only - does NOT fit AU Series 1. Some FG Falcon models use a different sensor - verify your OEM part number against the image before ordering. This sensor does not fit supercharged or turbocharged applications.

OEM PART NUMBERS

XS6F9F479AB
XS6F-9F479-AB
XS6F9F479AA
XS6F-9F479-AA
1086439
1087424

OTHER PART NUMBERS

Bosch: 0261230027
Continental/VDO: A2C59515232
Pierburg: 7.18222.11.0
HELLA: 6PP 009 400-531
VEMO: V25-72-0064-1
Walker Products: 225-1067
NTK-AU: EPBMPT4-A036Z

PACKAGE INCLUDES

1 x BRAND NEW MAP / air temperature sensor (4-pin oval connector). 1-bar pressure range (10-118 kPa). Direct OEM replacement - plug-in fitment, no wiring modification required.

ABOUT THIS SENSOR

The MAP (manifold absolute pressure) sensor measures the air pressure inside the intake manifold and feeds this data to the ECU. Combined with the integrated air temperature sensor, the ECU uses this information to calculate the correct air-fuel mixture, ignition timing, and idle control.

On the 5.4L Boss and Barra V8 engines, accurate MAP data is especially important for maintaining the high-performance fuel delivery that these engines are tuned for. A failing sensor causes flat spots, hesitation, and loss of power - often most noticeable at higher revs and under load.

COMMON SYMPTOMS OF FAILURE

Check Engine light with codes P0106 P0107 P0108 P0109
Flat spots or hesitation in acceleration especially above 3000 RPM
Rough idle or surging at low speed
Engine running rich - increased fuel consumption
Loss of power or performance under load
Hard starting or extended cranking

[03/99 - 12/02] FORD FALCON AU AUII AUIII 5.0L V8 Windsor MPFI Sedan/ Ute
[03/99 - 12/02] FORD FALCON AU AUII AUIII 5.0L V8 XR8 / 5.6L XR8 Pursuit Sedan/ Ute
[09/02 - 05/05] FORD FALCON BA XR8 5.4L V8 Boss 260 Sedan/ Ute
[09/02 - 05/05] FORD FALCON BA GT 5.4L V8 Boss Sedan
[09/02 - 05/05] FORD FALCON BA GTP 5.4L V8 Sedan
[09/02 - 05/05] FORD FALCON BA Pursuit 5.4L V8 Ute
[07/05 - 02/08] FORD FALCON BF XR8 5.4L V8 Boss 290 Sedan/ Ute
[07/05 - 02/08] FORD FALCON BF GT/ GT-P/ GT Cobra 5.4L V8 Sedan
[07/05 - 02/08] FORD FALCON BF Pursuit/ Super Pursuit 5.4L V8 Ute
[05/08 - 10/14] FORD FALCON FG XR8 5.4L V8 Boss 315 Sedan/ Ute
[05/08 - 10/14] FORD FALCON FG GT/ GT-E/ GT-P 5.4L V8 Sedan
[05/08 - 10/14] FORD FALCON FG GS/ Pursuit/ Super Pursuit 5.4L V8 Ute
[09/02 - 09/05] FORD FAIRLANE BA 5.4L V8 Sedan
[10/05 - 12/07] FORD FAIRLANE BF 5.4L V8 Sedan
[03/99 - 12/02] FORD FAIRMONT AU AUII AUIII 5.0L V8 Sedan
[09/02 - 05/05] FORD FAIRMONT BA 5.4L V8 Sedan
[07/05 - 02/08] FORD FAIRMONT BF 5.4L V8 Sedan
[03/99 - 12/02] FORD LTD AU 5.0L V8 Sedan
[09/02 - 09/05] FORD LTD BA 5.4L V8 Sedan
[10/05 - 12/07] FORD LTD BF 5.4L V8 Sedan
[02/04 - 09/07] FORD F-150 5.4L V8 AWD Utility
[09/99 - 12/01] FORD TICKFORD TE50/ TL50/ TS50 AU 5.0L-5.6L V8 Sedan

What fault codes does a faulty MAP sensor trigger?

A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.

How do I test a MAP sensor?

With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.

Can I drive with a faulty MAP sensor?

You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.

What does a MAP sensor do?

The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.

What are the symptoms of a faulty MAP sensor?

Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.

What is the difference between a MAP sensor and a MAF sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.

Identification
SKU	CMS216-5
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CMS216
Reference OEM Number	XS6F-9F479-AB
Other OEM Numbers	1086439, 1087424, XS6F9F479AA, XS6F9F479AB
Related Part Numbers	MP115, TMP008, MAP-012, 0261230028
Trade Part Numbers	Bosch: 0261230027, VEMO: V25-72-0064-1, NTK-AU: EPBMPT4-A036Z
Product Specifics
Product Type	SENSOR
Sensor Type	Manifold Absolute Pressure (MAP) Sensor
Number of pins	4-Pin
Connector Shape	oval
Pressure Range	10 kPa - 118 kPa
Number of mounting bores	1
Compatible Makes	Ford
Fitment Type	Direct Replacement
Other Details
Note	Fits AU Series 2 and 3 only. Does NOT fit AU Series 1.
Unit Of Measure	ea