BRAND NEW *OEM Quality* manifold absolute pressure (MAP) sensor to suit Suzuki Jimny and Grand Vitara 1.3L M13A 1.6L M16A 2.0L J20A and 2.7L H27A petrol engines.

A tired MAP sensor on these engines usually shows as a flat spot off idle and a rough cold start well before the check engine light comes on. This is a direct plug-in replacement using the correct 3-pin oval connector with no wiring modification. Packed and shipped from Cranbourne VIC.

TO SUIT

Suzuki Jimny SN413 JB33 and JB43 from 09/1998 to 10/2018 with the 1.3L G13BB and M13A engines. Suzuki Grand Vitara from the SQ416 1.6L G16B and SQ420 2.0L J20A series of 03/1998 through the JB416 TA74 1.6L M16A and JB420 TD54V 2.0L J20A to 02/2015. Also fits Vitara SV420 2.0L J20A and the LY series Vitara APK416 1.6L M16A from 05/2015.

FITMENT CHECK

On the Grand Vitara JB627 TD94V 2.7L V6 this sensor applies up to VIN JSAJTD94V00202878. Confirm your original sensor uses the 3-pin oval connector before ordering.

OEM PART NUMBERS

18590-72F21
18590-72F20
18590-72F21-000
18590-72F20-000
1859068H00
E1T26571A
91176190
71742176

OTHER PART NUMBERS

VEMO: V64-72-0035
HELLA: 6PP 358 152-231
NTY: ECM-SU-001
DELPHI: PS20085-12B1
MEYLE: 33-14 812 0000
VALEO: 367609
WALKER PRODUCTS: 225-1113
ACDelco: 213-1717
Goss: MP193
OEX: OMS223

PACKAGE INCLUDES

1 x MAP sensor with 3-pin oval connector and seal ring.

ABOUT THIS SENSOR

The MAP sensor reads absolute pressure inside the intake manifold and sends that signal to the ECU so it can calculate engine load and set fuelling and ignition timing. On the M13A Jimny and M16A Grand Vitara it mounts on the intake manifold and is exposed to constant heat cycling which slowly drifts its internal reference.

Once that reference drifts the ECU fuels against a false load reading. On these 4WD engines it shows first as poor throttle response under load and heavier fuel use on hills and in low range before any fault code is stored.

COMMON SYMPTOMS OF FAILURE

Flat spot or hesitation off idle
Rough or lumpy cold start on the 1.3L M13A
Noticeably higher fuel consumption when towing or in low range
Check engine light with P0105 P0106 P0107 or P0108
Black smoke or fuel smell from a rich running condition
Erratic idle once the engine reaches operating temperature

[09/98 - 09/02] SUZUKI JIMNY JB33/ SN413 16V (1.3L 4cyl G13BB 59kW)
[09/00 - 12/17] SUZUKI JIMNY JB43/ SN413 16V (1.3L 4cyl M13A 60kW)
[08/05 - 10/18] SUZUKI JIMNY JB43/ SN413 16V (1.3L 4cyl M13A 63kW)
[03/98 - 07/03] SUZUKI GRAND VITARA SQ416 I (1.6L 4cyl G16B 69kW)
[03/98 - 04/05] SUZUKI GRAND VITARA SQ420/ TA52/ TL52 I (2.0L 4cyl J20A 94kW)
[07/01 - 07/03] SUZUKI GRAND VITARA JA627 I (2.7L V6 H27A 130kW)
[04/03 - 07/08] SUZUKI GRAND VITARA JA627/ TX92 I (2.7L V6 H27A 135kW)
[09/05 - 02/15] SUZUKI GRAND VITARA JB416/ TA74 II (1.6L 4cyl M16A 73kW)
[09/05 - 02/15] SUZUKI GRAND VITARA JB420/ TD54V II (2.0L 4cyl J20A 103kW)
[12/05 - 12/09] SUZUKI GRAND VITARA JB627/ TD94V II (2.7L V6 H27A 136kW)
[05/97 - 03/98] SUZUKI VITARA SV420 16V (2.0L 4cyl J20A 97kW)
[05/97 - 04/00] SUZUKI VITARA SV420/ TA51 16V (2.0L 4cyl J20A 97kW)
[05/15 ON] SUZUKI VITARA APK416/ YD21S (1.6L 4cyl M16A 86kW)
[05/15 - 12/16] SUZUKI VITARA APK416/ YE21S (1.6L 4cyl M16A 86kW)
[07/00 - 10/04] TATA SAFARI 42_FD TDi (1.9L 4cyl 483 DL 64kW)

What fault codes does a faulty MAP sensor trigger?

A faulty MAP sensor typically triggers codes P0105 to P0109. P0105 indicates a circuit malfunction, P0106 indicates the signal is out of range, P0107 and P0108 indicate the signal is too low or too high respectively, and P0109 indicates an intermittent circuit fault. These codes combined with symptoms such as poor idle and black smoke are strong indicators of MAP sensor failure.

How do I test a MAP sensor?

With an OBD2 scanner in live data mode, the MAP sensor should read close to atmospheric pressure (around 101 kPa) with the engine off, and drop to 30 to 50 kPa at idle with the engine running due to manifold vacuum. Under wide open throttle the reading should rise back toward atmospheric. A sensor that reads flat or does not respond to throttle changes has failed. You can also test supply voltage and signal output with a multimeter.

Can I drive with a faulty MAP sensor?

You can drive short distances but engine performance will be noticeably degraded. The ECU uses the MAP sensor to calculate fuel delivery - a faulty sensor causes incorrect fuelling which leads to poor economy, rough running, and increased emissions. On turbocharged engines a faulty MAP sensor can also prevent boost control from operating correctly. Replace it as soon as possible to avoid further damage.

What does a MAP sensor do?

The Manifold Absolute Pressure (MAP) sensor measures intake manifold pressure to help the ECU calculate the correct fuel and ignition timing. It is critical for engine efficiency, particularly on turbocharged and supercharged vehicles.

What are the symptoms of a faulty MAP sensor?

Symptoms include poor acceleration, rough idle, excessive fuel consumption, black smoke, engine hesitation, and a Check Engine light with codes P0105-P0109. Turbocharged vehicles may also experience boost control issues.

What is the difference between a MAP sensor and a MAF sensor?

A MAF (Mass Air Flow) sensor directly measures the mass of air entering the engine. A MAP sensor measures manifold pressure and the ECU calculates air mass from that reading. Many vehicles use one or the other; some use both. They are not interchangeable.

Identification
SKU	CMS223
Brand	Aftermarket OEM Replacement
Part Numbers
Part Number	CMS223
Reference OEM Number	1859072F21
Other OEM Numbers	18590-72F21, 18590-72F20, E1T26571A, 91176190, 71742176
Related Part Numbers	MAP-035, CMS223, MP193, MAP1053, OMS223
Trade Part Numbers	VEMO: V64-72-0035, HELLA: 6PP 358 152-231, NTY: ECM-SU-001
Product Specifics
Product Type	SENSOR
Sensor Type	Manifold Absolute Pressure (MAP) Sensor
Number of pins	3-Pin
Connector Shape	oval
Mounting Type	Bolted
Pressure Range	10 kPa to 120 kPa
Number of mounting bores	2
Compatible Makes	Suzuki
Fitment Type	Direct Replacement
Other Details
Note	3-pin oval plug. Check connector shape before ordering.