Camshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8K Camshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8KCamshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8KCamshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8KCamshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8KCamshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8K

Camshaft Sensor for Mazda MX-5 NB 1.8L 1998-05 Convertible Turbo BP6J BP8K

Part #: 3931038050 OEM #: 39310-38050 SKU: 3931038050-Mazda

Direct Fit Replaces 3931038050

$119.97
RRP $223.95
SAVE $103.98 (46%)
In Stock

BRAND NEW OEM Quality CAMSHAFT POSITION SENSOR TO SUIT Mazda MX-5 NB 1.8L 1998-05 BP6J BP8K Engines

 

TO SUIT:

 

OEM#

39310-38030, 30874179, 3931038050, 3087417-9, 39310-38050,

J005T23071, J005T23071A, J5T23071, J5T23071A, MD327107

  • VEMO: V95-72-0018
  • NTY: ECP-HY-005
  • NTY: ECR-MS-001
  • WALKER PRODUCTS: 235-1051
  • WALKER PRODUCTS: 235-1124

 

PACKAGE INCLUDES:

1 X OEM CAMSHAFT POSITION SENSOR (3-PIN PLUG).

 

The camshaft sensor works with the crankshaft sensor to define the exact position of the crankshaft drive. The engine control unit knows when the first cylinder is at the top dead point through the combination of both sensor signals.

  • [04/02 - 10/05] MAZDA MX-5 NB Turbo 1.8L 4cyl BP Turbo/ BP8K 136kW
  • [01/02 - 10/02] MAZDA MX-5 NB Turbo 1.8L 4cyl BP8K 157kW
  • [05/98 - 10/05] MAZDA MX-5 NB8C 16V 1.8L 4cyl BP5A/ BP6J 103kW
  • [11/00 - 10/05] MAZDA MX-5 NB8C 16V 1.8L 4cyl BP6J 102kW
  • [11/00 - 10/05] MAZDA MX-5 NB8C 16V 1.8L 4cyl BP-ZE/ BP6J 107kW
  • [04/02 - 10/05] MAZDA MX-5 NB8C 1.8L 4cyl BP4W 113kW
How do I test a crankshaft or camshaft position sensor?

Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.

Can a cam or crank sensor fault cause my vehicle to go into limp mode?

Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.

Do cam and crank sensors need to be programmed after replacement?

In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.

What are the symptoms of a faulty crankshaft position sensor?

Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.

What are the symptoms of a faulty camshaft position sensor?

Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.

Can I drive with a bad crankshaft position sensor?

If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.

Do I need to replace both the cam and crank sensor at the same time?

Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.

Identification
SKU3931038050-Mazda
Barcode #4044079381383
BrandOEM
Part Numbers
Part Number3931038050
Reference OEM Number39310-38050
Other OEM Numbers3931038050, 33100-65D00, MD327107, J5T23071
Related Part NumbersCSCA87, SC271, SC265, SC241
Trade Part NumbersVEMO: V95-72-0018, NTY: ECP-HY-005, WALKER: 235-1051
Product Specifics
Product TypeSENSOR
Sensor TypeCAMSHAFT POSITION SENSOR
Number of pins3 -pin connector
Connector Shaperectangular
Supplementary Article Infowithout cable
Fitting Depth27 mm
Voltage12 V
Housing ColourBlack
Other Details
NoteAlways verify fitment using your vehicle's OEM part number.

Be The First To Review This Product!

Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category