








Camshaft Position Sensor for Hyundai iLoad iMax TQ 2.4L Petrol 39350-25010
Workshop Grade Replaces 39350-25010
BRAND NEW *OEM Quality* camshaft position sensor to suit Hyundai iLoad and iMax TQ 2.4L petrol models.
A failing camshaft sensor can trigger rough idle, stalling or a check engine light - this OEM Quality replacement restores accurate cylinder timing. Dispatched same-day from Cranbourne VIC.
TO SUIT
Fits Hyundai iLoad and iMax TQ models fitted with the 2.4L G4KC/G4KG petrol engine, produced 2008 to 2016. Confirm against the OEM number below before ordering.
OEM PART NUMBERS
- 39350-25010
- 39350-25000
- 3935025010
- 3935025000
OTHER PART NUMBERS
- VEMO: V52-72-0156
- NTK-AU: EC0311
- NTY: ECP-HY-008
- WALKER: 235-1245
PACKAGE INCLUDES
1 x camshaft position sensor, 3-pin connector.
ABOUT THIS SENSOR
The camshaft position sensor tells the engine control unit exactly where the camshaft is in its rotation, working with the crankshaft sensor to time fuel injection and ignition on the iLoad and iMax's 2.4L petrol engine.
A worn or failed sensor causes poor fuel economy, rough idle and can prevent the engine starting at all.
COMMON SYMPTOMS OF FAILURE
- Check engine light with camshaft position fault code (P0340/P0341)
- Rough or unstable idle
- Engine hesitation or stalling
- Difficulty starting
- Reduced fuel economy
- [02/08 - 11/16] HYUNDAI iLOAD TQ 2.4L 4cyl G4KC,G4KG 129kW
- [02/08 - 11/16] HYUNDAI iMAX TQ 2.4L 4cyl G4KC,G4KG 129kW
How do I test a crankshaft or camshaft position sensor?
Use an OBD2 scanner to check for fault codes P0335 to P0338 (crankshaft) or P0340 to P0349 (camshaft). You can also test the sensor with a multimeter - inductive sensors should show resistance between 200 and 1,000 ohms, while Hall effect sensors require a live voltage test with the engine cranking. Erratic or absent RPM signal on a live data scanner is a strong indicator of sensor failure.
Can a cam or crank sensor fault cause my vehicle to go into limp mode?
Yes. A faulty crankshaft position sensor in particular can cause the ECU to lose engine speed and position data entirely, which may trigger limp mode or prevent the engine from starting. A faulty camshaft sensor on variable valve timing engines can cause the VVT system to default to a fixed position, significantly reducing power and fuel economy.
Do cam and crank sensors need to be programmed after replacement?
In most cases no - aftermarket OEM replacement sensors are direct plug-in replacements that require no programming. However some vehicles, particularly late model European makes including BMW and Mercedes-Benz, may require a crankshaft adaptation reset using a dealer-level scan tool after replacement. Check your vehicle service information before replacing the sensor.
What are the symptoms of a faulty crankshaft position sensor?
Symptoms include intermittent stalling, engine not starting, rough idle, misfires, and a Check Engine light with codes P0335-P0338. In severe cases the engine will crank but not start as the ECU cannot determine crank position for ignition timing.
What are the symptoms of a faulty camshaft position sensor?
Symptoms include poor performance, misfires, difficulty starting, rough idle, and fault codes P0340-P0343. Variable valve timing systems (VVT) will also be affected, causing sluggish response and increased fuel consumption.
Can I drive with a bad crankshaft position sensor?
If the sensor has failed completely the engine will not start or will stall and not restart. If it is intermittently failing, driving is dangerous - the engine can cut out without warning. Replace it immediately.
Do I need to replace both the cam and crank sensor at the same time?
Not necessarily - replace whichever has failed based on fault codes and diagnosis. However, if your vehicle has high kilometres and one has failed, it is worth considering replacing both as they are similar in age and condition.
| Identification | |
|---|---|
| SKU | 3935025010-CSCA355 |
| Brand | OEM |
| Part Numbers | |
| Part Number | 3935025010 |
| Reference OEM Number | 39350-25010 |
| Other OEM Numbers | 3935025000, 3935025010, 39350-25000, 39350-25010 |
| Related Part Numbers | CSCA355, SC087, SC087GEN |
| Trade Part Numbers | VEMO: V52-72-0156, NTK-AU: EC0311, NTY: ECP-HY-008 |
| Product Specifics | |
| Product Type | SENSOR |
| Sensor Type | CAMSHAFT POSITION SENSOR |
| Manufacturer Warranty | 1 Year |
| Number of pins | 3-Pin |
| Connector Shape | oval |
| Housing Colour | Black |
| Fitment Type | Direct Replacement |
| Other Details | |
| Note | Always verify fitment using your vehicle's OEM part number. |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other SENSORGAL LTD. users shop smarter by writing reviews for products you have purchased.